Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 200:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SANITARY TAPWARE - SINGLE TAPS AND COMBINATION TAPS FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
Available format(s)

Hardcopy , PDF

Superseded date

11-01-2024

Language(s)

English

Published date

01-01-2008

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Designation
4 Marking and identification
5 Materials
6 Dimensional characteristics
7 Sequence of testing
8 Leaktightness characteristics
9 Pressure resistance characteristics - mechanical performance
   under pressure
10 Hydraulic characteristics
11 Mechanical strength characteristics - torsion test for
   operating mechanism
12 Mechanical endurance characteristics
13 Backflow protection
14 Acoustic characteristics
Annex A (informative) Pressure take-off tee
Bibliography

Pertains to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.

DevelopmentNote
Supersedes I.S. 287. (05/2017)
DocumentType
Standard
Pages
53
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NBN EN 200 : 2008 Identical
UNE-EN 200:2008 Identical
SN EN 200 : 2008 Identical
NF EN 200 : 2008 Identical
UNI EN 200 : 2008 Identical
BS EN 200:2008 Identical
EN 200:2008 Identical
NEN EN 200 : 2008 Identical
NS EN 200 : 3ED 2008 Identical
DIN EN 200:2008-10 Identical

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
EN 246:2003 Sanitary tapware - General specifications for flow rate regulators
EN 1112:2008 Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
EN 1254-2:1998 Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes
EN 1113:2015 SANITARY TAPWARE - SHOWER HOSES FOR SANITARY TAPWARE FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
ISO 3822-4:1997 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special appliances
EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 3822-4:1997 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances
EN 14506:2005 Devices to prevent pollution by backflow of potable water - Automatic diverter - Family H, type C
EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
ISO 3822-2:1995 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 2: Mounting and operating conditions for draw-off taps and mixing valves
ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
EN ISO 3822-2:1995 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995)
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 248:2002 Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr

View more information
$157.92
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more