We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 203-1:2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    GAS HEATED CATERING EQUIPMENT - PART 1: GENERAL SAFETY RULES

    Available format(s):  Hardcopy, PDF

    Superseded date:  27-01-2022

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Classification
    5 Constructional requirements
    6 Performance requirements
    7 Test conditions
    8 Designation
    9 Marking and instructions
    Annex A (informative) - National situations
    Annex B (normative) - Use of symbols on appliances
            and packaging
    Annex C (informative) - Trilingual list of appliances in
            the scope of EN 203-1 and corresponding Part 2
    Annex D (normative) - Non pneumatic air/gas control
            devices
    Annex E (informative) - Composition of the gas circuit
    Annex ZA (informative) - Clauses of this European
             Standard addressing essential requirements
             or other provisions of EU Directives
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the general requirements and the constructional and operating characteristics relating to safety, marking, and the associated test methods for gas heated commercial catering and bakery appliances.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-102: PARTICULAR REQUIREMENTS FOR GAS, OIL AND SOLID-FUEL BURNING APPLIANCES HAVING ELECTRICAL CONNECTIONS
    IEC 60730-2-9:2015 RLV Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls
    EN 10226-2 : 2005 PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 2: TAPER EXTERNAL THREADS AND TAPER INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
    EN 297:1994/A2:1996/AC:2006 GAS-FIRED CENTRAL HEATING BOILERS - TYPE B[11] AND B[11BS] BOILERS FITTED WITH ATMOSPHERIC BURNERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW
    EN 60730-2-9 : 2010 AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-9: PARTICULAR REQUIREMENTS FOR TEMPERATURE SENSING CONTROLS
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    EN ISO 3166-1 : 2014 CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES AND THEIR SUBDIVISIONS - PART 1: COUNTRY CODES (ISO 3166-1:2013)
    EN 161:2011+A3:2013 AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES
    EN ISO 228-1 : 2003 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
    EN 437:2003+A1:2009 TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES
    EN 125:2010+A1:2015 FLAME SUPERVISION DEVICES FOR GAS BURNING APPLIANCES - THERMOELECTRIC FLAME SUPERVISION DEVICES
    EN 126 : 2012 MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES
    CEN/TR 1749 : 2014 EUROPEAN SCHEME FOR THE CLASSIFICATION OF GAS APPLIANCES ACCORDING TO THE METHOD OF EVACUATION OF THE COMBUSTION PRODUCTS (TYPES)
    IEC 60730-2-1 : 1.0 AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PARTICULAR REQUIREMENTS FOR ELECTRICAL CONTROLS FOR ELECTRICAL HOUSEHOLD APPLIANCES
    EN 60335-2-102 : 2016 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-102: PARTICULAR REQUIREMENTS FOR GAS, OIL AND SOLID-FUEL BURNING APPLIANCES HAVING ELECTRICAL CONNECTIONS (IEC 60335-2-102:2004, MODIFIED + A1:2008, MODIFIED + A2:2012, MODIFIED)
    EN 60730-2-1 : 97 AMD 11 2005 AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-1: PARTICULAR REQUIREMENTS FOR ELECTRICAL CONTROLS FOR ELECTRICAL HOUSEHOLD APPLIANCES
    ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
    EN 1443 : 2003 CHIMNEYS - GENERAL REQUIREMENTS
    EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    EN 298 : 2012 AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS
    EN 1856-1 : 2009 CHIMNEYS - REQUIREMENTS FOR METAL CHIMNEYS - PART 1: SYSTEM CHIMNEY PRODUCTS
    EN 1106 : 2010 MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES
    ISO 301:2006 Zinc alloy ingots intended for castings
    EN 10226-1 : 2004 PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    EN 257 : 2010 MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective