I.S. EN 60137:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
Hardcopy , PDF
04-02-2020
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Ratings
5 Operating conditions
6 Ordering information and markings
7 Test requirements
8 Type tests
9 Routine tests
10 Requirements and tests for non-capacitance graded
bushings of rated highest voltages for equipment up to
and including 52 kV
11 Recommendations for transport, storage, erection,
operation and maintenance
12 Safety
13 Environmental aspects
Annex A (informative) - Determination of the hottest spot
in bushings with conductors embedded in the
insulation material
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Describes electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1000 V and power frequencies of 15 Hz up to and including 60 Hz.
| Committee |
TC 36
|
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| ISBN |
978-2-8322-4417-3
|
| Pages |
138
|
| ProductNote |
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60137:2017 | Identical |
| IEC 60137:2017 | Identical |
| BS EN 60137:2008 | Identical |
| SN EN 60137 : 2003 | Identical |
| NBN EN 60137 : 2010 | Identical |
| UNE-EN 60137:2011 | Identical |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| IEC 60480:2004 | Guidelines for the checking and treatment of sulfur hexafluoride (SF<sub>6</sub>) taken from electrical equipment and specification for its re-use |
| IEC 60038:2009 | IEC standard voltages |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEC 60076-7:2005 | Power transformers - Part 7: Loading guide for oil-immersed power transformers |
| EN 60376:2005 | Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment |
| EN 60422:2013 | Mineral insulating oils in electrical equipment - Supervision and maintenance guidance |
| IEC 62155:2003 | Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V |
| EN 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60050-471:2007 | International Electrotechnical Vocabulary (IEV) - Part 471: Insulators |
| EN 62155:2003 | Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V |
| IEC 62217:2012 | Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria |
| IEC 60422:2013 | Mineral insulating oils in electrical equipment - Supervision and maintenance guidance |
| IEC TS 60815-2:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems |
| EN 60076-5:2006 | Power transformers - Part 5: Ability to withstand short-circuit |
| EN 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60050-212:2010 | International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases |
| EN 60480:2004 | Guidelines for the checking and treatment of sulphur hexafluoride (SF6) taken from electrical equipment and specification for its re-use |
| EN 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| IEC 60076-5:2006 | Power transformers - Part 5: Ability to withstand short circuit |
| EN 61462:2007 | Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations |
| IEC 60376:2005 | Specification of technical grade sulfur hexafluoride (SF<sub>6</sub>) for use in electrical equipment |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| IEC 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| EN 60270:2001/A1:2016 | HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015) |
| IEC 60505:2011 | Evaluation and qualification of electrical insulation systems |
| EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| IEC 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60076-3:2013 | Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air |
| IEC 60050-421:1990 | International Electrotechnical Vocabulary (IEV) - Part 421: Power transformers and reactors |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 61462:2007 | Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations |
| EN 60068-2-17:1994 | Environmental testing - Part 2: Tests - Test Q: Sealing |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| IEC 60076-1:2011 | Power transformers - Part 1: General |
| IEC 62271-203:2011 | High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV |
| IEC TR 60943:1998+AMD1:2008 CSV | Guidance concerning the permissible temperature rise for parts of electrical equipment, in particular for terminals |
| IEC GUIDE 111:2004 | Electrical high-voltage equipment in high-voltage substations - Common recommendations for product standards |
| EN 60071-1:2006/A1:2010 | INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES |
| IEC 60867:1993 | Insulating liquids - Specifications for unused liquids based on synthetic aromatic hydrocarbons |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60076-2:2011 | Power transformers - Part 2: Temperature rise for liquid-immersed transformers |
| EN 60059:1999/A1:2009 | |
| IEC 60059:1999+AMD1:2009 CSV | IEC standard current ratings |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60507:2013 | Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| EN 60505:2011/AC:2017-03 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS (IEC 60505:2011/COR1:2017) |
| IEC TS 60815-1:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles |
| EN 62217:2013 | Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria |
| IEC TS 60815-3:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems |
| EN 60038 : 2011 | CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED) |
| IEC TS 61463:2016 | Bushings - Seismic qualification |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.