We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 61029-2-10:2010

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-10: PARTICULAR REQUIREMENTS FOR CUTTING-OFF GRINDERS (IEC 61029-2-10:1998 (MOD))

    Available format(s):  Hardcopy, PDF

    Superseded date:  22-12-2015

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Definitions
    3 General requirements
    4 General notes on tests
    5 Rating
    6 Classification
    7 Marking
    8 Protection against electric shock
    9 Starting
    10 Input and current
    11 Heating
    12 Leakage current
    13 Environmental requirements
    14 Protection against ingress of foreign bodies and
       moisture resistance
    15 Insulation resistance and electric strength
    16 Endurance
    17 Abnormal operation
    18 Stability and mechanical hazards
    19 Mechanical strength
    20 Construction
    21 Internal wiring
    22 Components
    23 Supply connection and external flexible cables and cords
    24 Terminals for external conductors
    25 Provision for earthing
    26 Screws and connections
    27 Creepage distances, clearances and distances through
       insulation
    28 Resistance to heat, fire and tracking
    29 Resistance to rusting
    30 Radiation
    Annex A (normative) Normative references
    Annex ZZ (informative) Coverage of Essential Requirements
             of Directive 2006/42/EC
    Annex ZD (informative) - Dust measurement

    Abstract - (Show below) - (Hide below)

    Applicable to cutting-off grinders intended to cut metal by means of a rotating abrasive cutting-off wheel: - with an abrasive cutting-off wheel diameter not exceeding 406 mm; - with a peripheral speed not exceeding 80 m/s.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
    ISO 1052:1982 Steels for general engineering purposes
    ISO 4997:2015 Cold-reduced carbon steel sheet of structural quality
    EN ISO 11688-1 : 2009 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING (ISO/TR 11688-1:1995)
    ISO 6316:2012 Hot-rolled steel strip of structural quality
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective