We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 61163-1:2006

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    RELIABILITY STRESS SCREENING - PART 1: REPAIRABLE ASSEMBLIES MANUFACTURED IN LOTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 General description
      5.1 The reliability stress screening principle
      5.2 Failure categories
      5.3 Time of occurrence of failures
    6 Planning
      6.1 Stress conditioning
      6.2 Evaluation of the failure-free period T[M]
      6.3 Time graphs for determination of the failure-free period
    7 Pilot-production screening
      7.1 General
      7.2 Collection of information
      7.3 Evaluation of information
      7.4 Re-evaluating the failure-free period T[M]
    8 Mature production screening
      8.1 General
      8.2 Collection of information
      8.3 Evaluation of information
      8.4 Dealing with discrepancies
      8.5 Eliminating reliability stress screening
    Annex A (informative) Stress conditions - General information
    Annex B (informative) Stress conditions - Temperature
    Annex C (informative) Stress conditions - Vibration and bump
    Annex D (informative) Stress conditions - Humidity
    Annex E (informative) Stress conditions - Operational stress
    Annex F (informative) Voltage stress
    Annex G (informative) Highly accelerated stress screening
    Annex H (informative) Bimodal distributions - Weibull plotting
                          and analysis
    Annex I (informative) Evaluation of the failure-free period
                          and the average screening duration
    Annex J (informative) Worked example
    Bibliography
    Annex ZA (normative) Normative references to international
                          publications with their corresponding
                          European publications

    Abstract - (Show below) - (Hide below)

    Describes particular methods to apply and optimize reliability stress screening processes for lots of repairable hardware assemblies, in cases where the assemblies have an unacceptably low reliability in the early failure period, and when other methods, such as reliability growth programmes and quality control techniques, are not applicable.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61649:2008 Weibull analysis
    IEC 61014:2003 Programmes for reliability growth
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    EN 60068-2-64 : 2008 ENVIRONMENTAL TESTING - PART 2-64: TESTS - TEST FH: VIBRATION, BROADBAND RANDOM AND GUIDANCE
    IEC 61165:2006 Application of Markov techniques
    IEC 60068-2-64:2008 Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance
    EN 61165 : 2006 APPLICATION OF MARKOV TECHNIQUES
    ISO 2041:2009 Mechanical vibration, shock and condition monitoring Vocabulary
    IEC 61164:2004 Reliability growth - Statistical test and estimation methods
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    IEC 60300-2:2004 Dependability management - Part 2: Guidelines for dependability management
    EN 60068-2-29 : 1993 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST EB AND GUIDANCE: BUMP
    EN 60068-2-78 : 2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    EN 60068-2-6 : 2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    IEC 60068-2-29:1987 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST EB AND GUIDANCE: BUMP
    EN 60068-2-30 : 2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    EN 60300-2 : 2004 DEPENDABILITY MANAGEMENT - PART 2: GUIDELINES FOR DEPENDABILITY MANAGEMENT
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    EN 60068-2-14 : 2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective