I.S. EN 61192-5:2007
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
WORKMANSHIP REQUIREMENTS FOR SOLDERED ELECTRONIC ASSEMBLIES - PART 5: REWORK, MODIFICATION AND REPAIR OF SOLDERED ELECTRONIC ASSEMBLIES
Hardcopy , PDF
29-05-2019
English
27-07-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
FOREWORD
1 Scope
2 Normative references
3 Terminology
3.1 Terms and definitions
3.2 Abbreviations
4 Classification of rework activities
4.1 Pre-soldering rework
4.2 Post-soldering rework
4.3 Essential prerequisites for successful and
reliable rework
5 Pre-soldering rework
5.1 General
5.2 Reworking solder paste and non-conducting adhesive
deposits
5.2.1 General
5.2.2 General misalignment or smudging of deposits
5.2.3 Local misalignment or smudging of deposit
5.2.4 General paste or adhesive quantity incorrect
5.2.5 Local paste or adhesive quantity incorrect
5.3 Reworking placed components
5.3.1 General overall component misalignment
5.3.2 Local component misalignment
5.4 Realigning components after curing thermoplastic
adhesive
5.5 Realigning components after curing thermosetting
adhesive
6 Factors affecting post-soldering rework
6.1 Component marking and unmarked components
6.2 Reuse of removed components
6.3 Sensitive components
6.4 Printed board layout design and space constraints
6.5 Heat-sink effects
6.6 Printed board material type
6.7 Solder resist material and aperture size
6.8 Reworking individual fine pitch device leads
6.9 Reworking grid arrays
7 Preparation for post-soldering rework and repair
7.1 Electrostatic precautions
7.2 Avoiding exposure of components to contaminants
7.3 Removal of conformal coating
7.4 Unsuitable components
7.5 Cleaning prior to rework
7.6 Protecting adjacent sensitive components
7.7 Baking of assemblies prior to component replacement
7.8 Preheating large multilayer boards
7.9 Preheating replacement sensitive components
8 Post-soldering rework
8.1 General
8.2 Component realignment (tweaking)
8.3 Component removal
8.4 Removal of adjacent components
8.5 Reuse of components
8.6 Addition of flux and solder
8.7 Topping-up
8.8 Removal of excess solder from joints
8.9 Preparation of lands before component replacement
8.10 Component replacement
8.11 Cleaning (if required)
8.12 Visual inspection and electrical testing
8.13 Checking thermal integrity of solder joints
8.14 Replacement of local conformal coating (if required)
9 Selection of rework equipment, tools and methods
9.1 General
9.2 Matching rework equipment to component and
printed-board prerequisites
9.2.1 General
9.2.2 Selection based on component types on the
printed board
printed board
9.2.3 Selection based on printed-board laminate
material type
9.2.4 Selection based on assembly structure and
soldering processes
10 Manual rework tools and methods
10.1 General
10.2 Miniature conventional (stored energy) soldering
irons
10.3 Directly heated soldering irons
10.4 Hot air/gas pencils
10.5 Heated tweezers
10.6 Soldering irons with special tips
11 Mechanized and programmable rework machines
11.1 General
11.2 Hot air rework machines
11.3 Focused infrared (IR) equipment
11.4 Thermode (heated electrode) equipment
11.5 Laser equipment for de-soldering
12 Ancillary tools and equipment
12.1 Conventional soldering irons
12.2 Hotplates
12.3 Pneumatic dispensers
12.4 De-soldering tools, as used for through-hole
assemblies
12.5 Tweezers and vacuum pencils
12.6 Solder pots
12.7 Copper braid
13 Rework recording procedures
13.1 General
13.2 Anomaly charts
13.3 Travelling documents
13.4 Rework status
14 Training of operators and inspectors
15 Field repair
Bibliography
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.