We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN ISO 22475-1:2006

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    GEOTECHNICAL INVESTIGATION AND TESTING - SAMPLING METHODS AND GROUNDWATER MEASUREMENTS - PART 1: TECHNICAL PRINCIPLES FOR EXECUTION

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-11-2021

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
       3.1 Site investigation methods
       3.2 Drilling rigs and equipment
       3.3 Sampling
       3.4 Groundwater measurements
    4 Drilling rigs and ancillary equipment
       4.1 General
       4.2 Requirements for the drilling rigs and equipment
       4.3 Equipment scope
    5 General requirements prior to sampling and groundwater
       measurements
       5.1 General
       5.2 Selection of techniques and methods
       5.3 Requirements for ground investigation sites and
            points
       5.4 Preliminary information needed before starting
            sampling and groundwater measurements
       5.5 Backfilling and site abandonment
       5.6 Safety and special requirements
    6 Soil sampling methods
       6.1 General
       6.2 Categories of soil sampling methods
       6.3 Sampling by drilling (continuous sampling)
       6.4 Sampling using samplers
       6.5 Block sampling
    7 Rock sampling methods
       7.1 General
       7.2 Categories for rock sampling methods
       7.3 Sampling by drilling
       7.4 Block sampling
       7.5 Integral sampling
    8 Groundwater sampling methods for geotechnical purposes
       8.1 General
       8.2 Equipment
       8.3 Techniques of groundwater sampling
    9 Groundwater measuring stations and piezometers
       9.1 General
       9.2 Piezometers
       9.3 Installation of piezometers
       9.4 Maintenance
       9.5 Decommissioning
    10 Groundwater measurements
       10.1 Calibration
       10.2 Performance of the measurements
    11 Handling, transport and storage of samples
       11.1 General
       11.2 Preservation materials and sample containers
       11.3 Handling of samples
       11.4 Labelling of samples
       11.5 Transport of samples
       11.6 Preparation of storage and shipping containers
       11.7 Storage of samples
    12 Report
       12.1 Field report
       12.2 Report of the results
    Annex A (informative) Example of a form for the preliminary
                          information on the intended sampling
                          and groundwater measurements
    Annex B (informative) Field reports
    Annex C (informative) Drilling and sampling equipment for
                          soil and rock
    Annex D (informative) Vacuum bottles for groundwater sampling
    Annex E (informative) Protective measures of piezometers
    Bibliography

    Abstract - (Show below) - (Hide below)

    Deals with the technical principles of sampling soil, rock and groundwater, and with groundwater measurements, in the context of geotechnical investigation and testing, as described in EN 1997-1 and EN 1997-2.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 14688-1:2002 Geotechnical investigation and testing Identification and classification of soil Part 1: Identification and description
    EN 996:1995+A3:2009 Piling equipment - Safety requirements
    ISO 10097-1:1999 Wireline diamond core drilling equipment — System A — Part 1: Metric units
    EN 791:1995+A1:2009 Drill rigs - Safety
    ISO 14689-1:2003 Geotechnical investigation and testing Identification and classification of rock Part 1: Identification and description
    ISO 22476-3:2005 Geotechnical investigation and testing Field testing Part 3: Standard penetration test
    ISO 3552-1:1992 Rotary core diamond drilling equipment — System B — Part 1: Metric units
    EN 1997-2:2007/AC:2010 EUROCODE 7 - GEOTECHNICAL DESIGN - PART 2: GROUND INVESTIGATION AND TESTING
    ISO 3551-1:1992 Rotary core diamond drilling equipment — System A — Part 1: Metric units
    EN 1997-1:2004/A1:2013 EUROCODE 7: GEOTECHNICAL DESIGN - PART 1: GENERAL RULES
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more