Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

IEC 61045-1:1991

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Fixed film resistor networks for use in electronic equipment - Part 1: Generic specification
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

08-10-2009

Language(s)

English - French

Published date

19-03-1991

Foreword
Preface
SECTION ONE - SCOPE
Clause
1 Scope
SECTION TWO - GENERAL
2 General
   2.1 Related documents
   2.2 Units, symbols and terminology
   2.3 Preferred values
   2.4 Marking
SECTION THREE - QUALITY ASSESSMENT PROCEDURES
3 Quality assessment procedures
   3.1 Qualification Approval/Quality Assessment Systems
   3.2 Primary Stage of Manufacture
   3.3 Manufacturing stages in a Factory of an approved
        manufacturer in a non-IECQ Member Country and
        Sub-contracting
   3.4 Manufacturer Approval
   3.5 Approval procedures
   3.6 Qualification Approval Procedures
   3.7 Capability Approval Procedures
   3.8 Quality Conformance Inspection
   3.9 Alternative test methods
   3.10 Unchecked parameters
SECTION FOUR - TEST AND MEASUREMENT PROCEDURES
4 Test and measurement procedures
   4.1 General
   4.2 Standard atmospheric conditions
   4.3 Drying
   4.4 Visual examination and check of dimensions
   4.5 Resistance
   4.6 Resistance ratio
   4.7 Functional characteristics
   4.8 Insulation resistance (insulated styles only)
   4.9 Voltage proof (insulated networks only)
   4.10 Variation of resistance with temperature
   4.11 Non-linear properties
   4.12 Overload
   4.13 Robustness of terminations
   4.14 Solderability
   4.15 Resistance to soldering heat
   4.16 Rapid change of temperature
   4.17 Shock
   4.18 Vibration
   4.19 Climatic sequence
   4.20 Damp heat, steady state
   4.21 Endurance
   4.22 Component solvent resistance
   4.23 Solvent resistance of the marking
Appendix A: Interpretation of sampling plans and
            procedures as described in IEC Publication
            410 for use within the IEC Quality Assessment
            System for Electronic Components
Appendix B: Rules for the preparation of detail
            specification for capacitors and resistors for
            electronic equipment

Establishes standard terms, inspection procedures and methods oftest for qualification and capability approval.

DevelopmentNote
Also numbered as BS QC390000(1992) (08/2005)
DocumentType
Standard
Pages
89
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy

Standards Relationship
SAC GB/T 15654 : 1995 Identical
NEN 11045-1 : 1991 Identical
NEN 11045-2 : 1991 Identical

BS QC 390101:1992 Fixed film resistor networks for use in electronic equipment. Blank detail specification for film resistor networks of assessed quality on the basis of the capability approval procedure. Assessment level E
IEC 61045-2:1991 Fixed film resistor networks for use in electronic equipment - Part 2: Sectional specification for film resistor networks of assessed quality on the basis of the capability approval procedure
BS QC 390100:1992 Harmonized system of quality assessment for electronic components. Fixed film resistor networks for use in electronic equipment. Sectional specification for film resistor networks of assessed quality on the basis of the capability approval procedure

IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
ISO 3:1973 Preferred numbers Series of preferred numbers
IEC 60027-1:1992 Letters symbols to be used in electrical technology - Part 1: General
IEC 60191-2:2012 DB Mechanical standardization of semiconductor devices - Part 2: Dimensions
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
IEC 60068-2-3:1969 Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC TR 60440:1973 Method of measurement of non-linearity in resistors
IEC 60062:2016 Marking codes for resistors and capacitors
IEC 60063:2015 Preferred number series for resistors and capacitors
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
IEC 60717:2012 Method for the determination of the space required by capacitors and resistors with unidirectional terminations
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60195:2016 Method of measurement of current noise generated in fixed resistors
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
$661.46
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more