Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

IEC 62196-3:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

19-10-2022

Language(s)

English - French, Spanish, Castilian

Published date

19-06-2014

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Ratings
6 Connection between the power supply and the electric vehicle
7 Classification of accessories
8 Marking
9 Dimensions
10 Protection against electric shock
11 Size and colour of earthing conductors
12 Provision for earthing
13 Terminals
14 Interlocks
15 Resistance to aging of rubber and thermoplastic material
16 General construction
17 Construction of socket-outlets
18 Construction of plugs and vehicle connectors
19 Construction of vehicle inlets
20 Degrees of protection
21 Insulation resistance and dielectric strength
22 Breaking capacity
23 Normal operation
24 Temperature rise
25 Flexible cables and their connection
26 Mechanical strength
27 Screws, current-carrying parts and connections
28 Creepage distances, clearances and distances
29 Resistance to heat, to fire and to tracking
30 Corrosion and resistance to rusting
31 Conditional short-circuit current withstand test
32 Electromagnetic compatibility
33 Vehicle driveover
Bibliography

IEC 62196-3:2014 is applicable to vehicle couplers with pins and contact-tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V d.c. and rated current up to 250 A, and 1 000 V a.c. and rated current up to 250 A. This part of IEC 62196 applies to high power d.c. interfaces and combined a.c./d.c. interfaces of vehicle couplers specified in IEC 62196-1:2014, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010, and IEC 61851-23:2014.

This publication is to be read in conjunction with IEC 62196-1:2014.

Committee
TC 23/SC 23H
DevelopmentNote
To be read in conjunction with IEC 62196-1. Stability date: 2018. (06/2014)
DocumentType
Standard
Pages
71
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy

BS ISO 15118-3 : 2015 ROAD VEHICLES - VEHICLE TO GRID COMMUNICATION INTERFACE - PART 3: PHYSICAL AND DATA LINK LAYER REQUIREMENTS
12/30257420 DC : 0 BS EN 61851-23 ED 1.0 - ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: D.C. ELECTRIC VEHICLE CHARGING STATION
BS EN 61851-23:2014 Electric vehicle conductive charging system DC electric vehicle charging station
ISO 15118-3:2015 Road vehicles — Vehicle to grid communication interface — Part 3: Physical and data link layer requirements
DIN EN ISO 17409:2016-09 (Draft) ELECTRICALLY PROPELLED ROAD VEHICLES - CONNECTION TO AN EXTERNAL ELECTRIC POWER SUPPLY - SAFETY REQUIREMENTS (ISO 17409:2015, CORRECTED VERSION 2015-12-15)
BS ISO 17409 : 2015 ELECTRICALLY PROPELLED ROAD VEHICLES - CONNECTION TO AN EXTERNAL ELECTRIC POWER SUPPLY - SAFETY REQUIREMENTS
BS IEC 62394 : 2017 SERVICE DIAGNOSTIC INTERFACE FOR CONSUMER ELECTRONICS PRODUCTS AND NETWORKS - IMPLEMENTATION FOR ECHONET
I.S. EN 61851-23:2014 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION
I.S. EN ISO 17409:2017 ELECTRICALLY PROPELLED ROAD VEHICLES - CONNECTION TO AN EXTERNAL ELECTRIC POWER SUPPLY - SAFETY REQUIREMENTS (ISO 17409:2015, CORRECTED VERSION 2015-12-15)
SAE J 2847/6 : 2015 COMMUNICATION BETWEEN WIRELESS CHARGED VEHICLES AND WIRELESS EV CHARGERS
IEC 61851-1:2017 Electric vehicle conductive charging system - Part 1: General requirements
VDI 2166 Blatt 2:2015-10 Planning of electrical installations in buildings - Advice for electric mobility
DIN EN ISO 17409 E : 2017 ELECTRICALLY PROPELLED ROAD VEHICLES - CONNECTION TO AN EXTERNAL ELECTRIC POWER SUPPLY - SAFETY REQUIREMENTS (ISO 17409:2015, CORRECTED VERSION 2015-12-15)
IEC 62394:2017 Service diagnostic interface for consumer electronics products and networks - Implementation for ECHONET
IEEE 2030.1.1-2015 IEEE Standard Technical Specifications of a DC Quick Charger for Use with Electric Vehicles
UNE-EN ISO 17409:2017 Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements (ISO 17409:2015, Corrected version 2015-12-15)
BS EN ISO 15118-3:2016 Road vehicles. Vehicle to grid communication interface Physical and data link layer requirements
BS EN ISO 17409:2017 Electrically propelled road vehicles. Connection to an external electric power supply. Safety requirements
SAE J 3068 :2018 ELECTRIC VEHICLE POWER TRANSFER SYSTEM USING A THREE-PHASE CAPABLE COUPLER
I.S. EN ISO 15118-3:2016 ROAD VEHICLES - VEHICLE TO GRID COMMUNICATION INTERFACE - PART 3: PHYSICAL AND DATA LINK LAYER REQUIREMENTS (ISO 15118-3:2015)
IEC TR 61850-90-8:2016 Communication networks and systems for power utility automation - Part 90-8: Object model for E-mobility
UNE-EN 61851-23:2015 Electric vehicle conductive charging system - Part 23: DC electric vehicle charging station
15/30269927 DC : 0 BS EN 61851-1 ED 3.0 - ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM PART 1: GENERAL REQUIREMENTS
EN ISO 15118-3:2016 Road vehicles - Vehicle to grid Communication interface - Part 3: Physical and data link layer requirements (ISO 15118-3:2015)
SAE J 2847/2 : 2015 COMMUNICATION BETWEEN PLUG-IN VEHICLES AND OFF-BOARD DC CHARGERS
PD IEC/TR 61850-90-8:2016 Communication networks and systems for power utility automation Object model for E-mobility
CSA C22.2 No. 282 : 2013 PLUGS, RECEPTACLES, AND COUPLERS FOR ELECTRIC VEHICLES
ISO 17409:2015 Electrically propelled road vehicles Connection to an external electric power supply Safety requirements
EN ISO 17409:2017 Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirements (ISO 17409:2015, Corrected version 2015-12-15)
EN 61851-23:2014/AC:2016-06 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION (IEC 61851-23:2014/COR1:2016)

IEC 62196-2:2016 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
ISO 17409:2015 Electrically propelled road vehicles Connection to an external electric power supply Safety requirements

View more information
$442.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more