We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • IEC TS 60859:1999

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Cable connections for gas-insulated metal-enclosed switchgear for rated voltages of 72,5 kV and above - Fluid-filled and extruded insulation cables - Fluid-filled and dry type cable-terminations

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  09-08-2007

    Language(s): 

    Published date:  29-07-1999

    Publisher:  International Electrotechnical Committee

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Definitions
    4 Limits of supply
    5 Rating
          5.1 Rated voltage
          5.2 Number of phases in one enclosure
          5.3 Rated insulation level
          5.4 Rated normal current and temperature rise
          5.5 Rated short-time and peak withstand currents
                 and rated duration of short circuit
    6 Design and construction requirements
          6.1 Pressure withstand requirements
          6.2 Mechanical forces on cable-terminations
    7 Standard dimensions
          7.1 Fluid-filled cable-terminations
          7.2 Dry type cable-terminations
    8 Tests
          8.1 General
          8.2 Dielectric type tests
                 8.2.1 Dielectric type tests of cable-
                          terminations
                 8.2.2 Dielectric type test of cable
                          connection enclosures
          8.3 Tests after cable installation
    9 Information to be given with enquiries, tenders
          and orders
    10 Rules for transport, storage, erection, operation
          and maintenance
    Figure 1 - Fluid-filled cable connection assembly -
               Typical arrangement
    Figure 2 - Fluid-filled cable connection assembly -
               Dimensions
    Figure 3 - Dry type cable connection assembly -
               Typical arrangements
    Figure 4 - Dry type cable connection assembly -
               Dimensions
    Figure 5 - Non-symmetrical arrangement for dielectric
               tests of cable terminations

    Abstract - (Show below) - (Hide below)

    Covers the connection assembly of cables to gas-insulated metal-enclosed switchgear in single- or three-phase arrangements where the cable terminations are fluid-filled and there is a separating insulating barrier between the cable insulation and the gas insulation of the switchgear.The contents of corrigenda of February 2000 and December 2000 have been included in this copy.

    General Product Information - (Show below) - (Hide below)

    Committee TC 17/SC 17C
    Document Type Technical Specification
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 7923(2004) : 2004 ELECTRIC CABLES - INTERNAL GAS-PRESSURE CABLES AND ACCESSORIES FOR ALTERNATING VOLTAGES UP TO AND INCLUDING 275 KV (U[M] = 300 KV) - REQUIREMENTS AND TEST METHODS
    BS EN 45510-2-7 : 2002 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
    BIS IS/IEC 62271-203 : 2003 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES ABOVE 52 KV
    IEEE DRAFT C37.123 : D2 FEB 96 DRAFT GUIDE TO SPECIFICATIONS FOR GAS-INSULATED ELECTRIC POWER SUBSTATION EQUIPMENT
    BS 7922(2004) : 2004 ELECTRIC CABLES - FLUID-FILLED, PAPER- AND PPL-INSULATED, METAL-SHEATHED CABLES AND ACCESSORIES FOR ALTERNATING VOLTAGES UP TO AND INCLUDING 400 KV (U[M] = 420 KV) - REQUIREMENTS AND TEST METHODS
    EN 45510-2-7 : 2002 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-7: ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60517:1990 Gas-insulated metal-enclosed switchgear for rated voltages of 72.5 kV and above
    IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
    IEC 60141-1:1993 Tests on oil-filled and gas-pressure cables and their accessories - Part 1: Oil-filled, paper or polypropylene paper laminate insulated, metal-sheathed cables and accessories for alternating voltages up to and including 500 kV
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective