We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ISO 22621-3:2007

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 3: Fittings

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Withdrawn date:  01-06-2012

    Language(s):  English, Russian

    Published date:  01-11-2007

    Publisher:  International Organization for Standardization

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 22621 specifies the physical and mechanical properties of fittings made from polyamide (PA) in accordance with ISO 22621-1, intended to be buried and used for the supply of gaseous fuels at maximum operating pressures (MOP) up to and including 2 MPa (20 bar).

    It also specifies the test parameters for the test methods to which it refers.

    In addition, it lays down dimensional characteristics and requirements for the marking of fittings.

    In conjunction with the other parts of ISO 22621, it is applicable to PA fittings, their joints, to joints with components of PA and to joints with mechanical fittings of other materials, and to the following fitting types: fusion fittings (electrofusion and butt fusion fittings); transition fittings.

    General Product Information - (Show below) - (Hide below)

    Committee ISO/TC 138/SC 4
    Development Note Supersedes ISO/DIS 22621-3. (11/2007)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Withdrawn
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS ISO 22621-5 : 2010 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURES UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
    05/30130524 DC : DRAFT MAR 2005 ISO 22621-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 1: GENERAL
    BS PAS 600(2013) : 2013 BIO-BASED PRODUCTS - GUIDE TO STANDARDS AND CLAIMS
    09/30181333 DC : 0 BS ISO 22621-6 ISO/CD 22621-6 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURES UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 6: CODE OF PRACTICE FOR DESIGN, HANDLING AND INSTALLATION
    BS ISO 22621-6 : 2010 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURES UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 6: CODE OF PRACTICE FOR DESIGN, HANDLING AND INSTALLATION
    09/30175820 DC : 0 BS ISO 22621-5 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
    ISO 22621-6:2010 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 6: Code of practice for design, handling and installation
    ISO 22621-5:2010 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 5: Fitness for purpose of the system

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 22621-2:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 2: Pipes
    EN 682:2002/A1:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
    ISO 13953:2001 Polyethylene (PE) pipes and fittings Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 4433-1:1997 Thermoplastics pipes Resistance to liquid chemicals Classification Part 1: Immersion test method
    ISO 13957:1997 Plastics pipes and fittings Polyethylene (PE) tapping tees Test method for impact resistance
    IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 307:2007 Plastics Polyamides Determination of viscosity number
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 22621-1:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 1: General
    ISO 13951:2015 Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective