ISO 6162-1 : 2012(R2018)

Current

Current The latest, up-to-date edition.

Preview

HYDRAULIC FLUID POWER - FLANGE CONNECTIONS WITH SPLIT OR ONE-PIECE FLANGE CLAMPS AND METRIC OR INCH SCREWS - PART 1: FLANGE CONNECTORS, PORTS AND MOUNTING SURFACES FOR USE AT PRESSURES OF 3,5 MPA (35 BAR) TO 35 MPA (350 BAR), DN 13 TO DN 127

Publisher: International Organization for Standardization

Published: 01-01-2012

Available Formats: PDF - English, Hardcopy - English, PDF - French, Hardcopy - French
More Info on product formats

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Material
5 Selection
6 Dimensions and tolerances
7 Corrosion protection
8 Pressure/temperature requirements
9 Marking
10 Designation of flange connections and
   their parts
Annex A (informative) - Recommended assembly
        procedures and screw torque levels for
        flange connections conforming to ISO 6162-1
Annex B (informative) - O-ring designation codes and
        dimensions
Bibliography

Abstract - (Show below) - (Hide below)

Provides general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar).

General Product Information - (Show below) - (Hide below)

Published
Document Type	Revision
Status	Current
Publisher	International Organization for Standardization
Pages
ISBN
Committee	TC 131
Supersedes	ISO 6162 : 1994 ISO 6162-1 : 2002 ISO/DIS 6162-1 : 60.00 (2012)

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
BS ISO 6162-1 : 2012	Identical
NF ISO 6162-1 : 2013	Identical
NEN ISO 6162-1 : 2012	Identical
NF ISO 6162-1 : 2013	Identical
DIN ISO 6162-1 : 2006	Identical
BS ISO 6162-1 : 2012	Identical
DIN ISO 6162-1 E : 2006	Identical
SN ISO 6162-1 : 2005 CORR 2005	Identical
NEN ISO 6162-1 : 2012	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

03/110806 DC : DRAFT JUNE 2003	BS ISO 19879 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
DIN ISO 6022 E : 2008	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
14/30274168 DC : 0	BS ISO 6020-3 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM
DIN ISO 6022 : 2008	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
09/30202316 DC : 0	BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES
BS ISO 6020-1 : 2007	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
DIN EN ISO 4413 E : 2011	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
SAE J 2551/2 : 2013	RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS
BS PD ISO/TS 11672 : 2016	CONNECTORS FOR FLUID POWER AND GENERAL USE - DESIGNATION AND NOMENCLATURE
SAE J 1065 : 2016	NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING
SAE J 2614 : 2018	WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING
SAE J 2551/3 : 2013	RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT
16/30328245 DC : 0	BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80
14/30284271 DC : 0	BS ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
UNI ISO 12151-3 : 2012	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
ISO 12151-3 : 2010(R2015)	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
SAE J 2551 : 2013	RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON AND ALLOY STEEL TUBING APPLICATIONS
BS EN ISO 4413 : 2010	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
DIN ISO 12151-3 E : 2012	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS (ISO 12151-3:2010)
UNI ISO 17165-1 : 2012	HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS
BS ISO 12151-3 : 2010	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
BS ISO 6020-2 : 2015	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
BS ISO 4081 : 2016	RUBBER HOSES AND TUBING FOR COOLING SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION
DIN ISO 12151-3 : 2012	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS (ISO 12151-3:2010)
BS ISO 16874 : 2004	HYDRAULIC FLUID POWER - IDENTIFICATION OF MANIFOLD ASSEMBLIES AND THEIR COMPONENTS
BS ISO 17165-1 : 2007	HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS
04/30098195 DC : DRAFT JUL 2004	ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
DIN ISO 6020-1 : 2010	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
ISO 6022 : 2006(R2017)	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
SAE J 846 : 2015	CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS
07/30163202 DC : 0	BS ISO 12151-3 - CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
09/30193685 DC : 0	BS ISO 4081 - RUBBER HOSES AND TUBING FOR COOLING SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION
BS ISO 6020-3 : 2015	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM
BS ISO 6022 : 2006	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
BS ISO 10946 : 1999	HYDRAULIC FLUID POWER - GAS-LOADED ACCUMULATORS WITH SEPARATOR - SELECTION OF PREFERRED HYDRAULIC PORTS
06/30128831 DC : DRAFT MAR 2006	ISO 6020-1 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
BS PD ISO/TS 17165-2 : 2013	HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 2: PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES
SAE J 518/1 : 2013	HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 1: 3.5 MPA TO 35 MPA (CODE 61)
DIN ISO 6020-1 E : 2010	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
ISO 4081 : 2016	RUBBER HOSES AND TUBING FOR COOLING SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION
DIN EN ISO 4413 : 2011	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
UNE EN ISO 4413 : 2011	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS (ISO 4413:2010)
NF EN ISO 4413 : 2011	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
SAE J 2551/1 : 2013	RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION
SAE J 2593 : 2015	INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS
ISO 6020-1 : 2007	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
SAE J 515 : 2015	SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS
ISO 6164 : 1994	HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 25 TO 80
ISO 17165-1:2007(R2011)	HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS
SAE J 1677 : 2016	TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING
NF ISO 12151-3 : 2010	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
SAE J 518/2 : 2017	HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 2: 42 MPA (CODE 62)
DIN EN ISO 19879 : 2011	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
04/30098199 DC : DRAFT JUL 2004	ISO 6022 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
ISO 16874 : 2004(R2014)	HYDRAULIC FLUID POWER - IDENTIFICATION OF MANIFOLD ASSEMBLIES AND THEIR COMPONENTS
SAE J 518/3 : 2015	HYDRAULIC FLANGE CLAMPS, 2-SCREW FLANGE CONNECTION TO BE USED WITH SAE J518-1, (CODE 61) CONNECTIONS WHERE ONLY LOW PRESSURE IS REQUIRED
ISO 6020-3 : 2015	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM
ISO 6020-2 : 2015	HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
DIN EN ISO 19879 E : 2011	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
DIN EN ISO 16330 E : 2004	RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS
DIN EN ISO 16330 : 2004	RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS
UNE-EN ISO 19879:2010	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
ISO 19859 : 2016-06	GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
14/30244780 DC : 0	BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
BS EN ISO 19879 : 2010	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
BS EN ISO 16330 : 2003	RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS
ISO 4413 : 2010(R2016)	HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
BS ISO 19859 : 2016	GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
ISO 16330 : 2003(R2018)	RECIPROCATING POSITIVE DISPLACEMENT PUMPS - TECHNICAL REQUIREMENTS
ISO 19879 : 2010	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS

Standards Referencing This Book - (Show below) - (Hide below)

ISO 68-2 : 1998(R2014)	ISO GENERAL PURPOSE SCREW THREADS - BASIC PROFILE - PART 2: INCH SCREW THREADS
ISO 5598 : 2008	FLUID POWER SYSTEMS AND COMPONENTS - VOCABULARY
ISO 1101 : 2017	GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUN-OUT
SAE J 429 : 2014	MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
ISO 724 : 1993(R2014)	ISO METRIC SCREW THREADS - BASIC DIMENSIONS
ISO 4017 : 2014	FASTENERS - HEXAGON HEAD SCREWS - PRODUCT GRADES A AND B
ISO 6708 : 1995(R2015)	PIPEWORK COMPONENTS - DEFINITION AND SELECTION OF DN (NOMINAL SIZE)
ISO 4762 : 2004(R2018)	HEXAGON SOCKET HEAD CAP SCREWS
ISO 5864 : 1993(R2014)	ISO INCH SCREW THREADS - ALLOWANCES AND TOLERANCES
ISO 1302 : 2002(R2012)	GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION
SAE J 515 : 2015	SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS
ISO 12151-3 : 2010(R2015)	CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
ISO 7089 : 2000(R2016)	PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE A
ISO 68-1 : 1998(R2014)	ISO GENERAL PURPOSE SCREW THREADS - BASIC PROFILE - PART 1: METRIC SCREW THREADS
ISO 19879 : 2010	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
ISO 6164 : 1994	HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 25 TO 80
ISO 80000-1 : 2009	QUANTITIES AND UNITS - PART 1: GENERAL
ISO 725 : 2009(R2014)	ISO INCH SCREW THREADS - BASIC DIMENSIONS
ISO 273 : 1979(R2014)	FASTENERS - CLEARANCE HOLES FOR BOLTS AND SCREWS
ASME B18.3 : 2012	SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES)
ISO 9227 : 2017	CORROSION TESTS IN ARTIFICIAL ATMOSPHERES - SALT SPRAY TESTS
ISO 261 : 1998(R2014)	ISO GENERAL PURPOSE METRIC SCREW THREADS - GENERAL PLAN
ISO 10763:1994(R2011)	HYDRAULIC FLUID POWER - PLAIN-END, SEAMLESS AND WELDED PRECISION STEEL TUBES - DIMENSIONS AND NOMINAL WORKING PRESSURES
ISO 3601-1 : 2012(R2017)	FLUID POWER SYSTEMS - O-RINGS - PART 1: INSIDE DIAMETERS, CROSS-SECTIONS, TOLERANCES AND DESIGNATION CODES
ASME B18.22.1 : 1965	PLAIN WASHERS
ASTM A 574 : 2017 : REDLINE	Standard Specification for Alloy Steel Socket-Head Cap Screws
ISO 13715 : 2017	TECHNICAL PRODUCT DOCUMENTATION - EDGES OF UNDEFINED SHAPE - INDICATION AND DIMENSIONING
ISO 3601-3 : 2005(R2016)	FLUID POWER SYSTEMS - O-RINGS - PART 3: QUALITY ACCEPTANCE CRITERIA
ISO 48 : 2010	RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF HARDNESS (HARDNESS BETWEEN 10 IRHD AND 100 IRHD)
ISO 263 : 1973(R2015)	ISO INCH SCREW THREADS - GENERAL PLAN AND SELECTION FOR SCREWS, BOLTS AND NUTS - DIAMETER RANGE 0,06 TO 6 IN
ISO 898-1 : 2013(R2018)	MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD
ISO 2768-1 : 1989	GENERAL TOLERANCES - PART 1: TOLERANCES FOR LINEAR AND ANGULAR DIMENSIONS WITHOUT INDIVIDUAL TOLERANCE INDICATIONS

Add To Cart

Product Format

Quantity

add to cart

ISO 6162-1 : 2012(R2018)

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Standards Referenced By This Book - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?