ISO 899-2:2003
Current
Current
The latest, up-to-date edition.
Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
Amended by
Available format(s)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
Published date
03-06-2003
ISO 899-2:2003 specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pretreatment, temperature and humidity. It applies only to a simple freely supported beam loaded at mid-span (three-point-loading test).
The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) in the form of dumb-bell-shaped test specimens moulded directly or machined from sheets or moulded articles.
NOTE The method may be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation.
The method is intended to provide data for engineering-design and research and development purposes. Data for engineering-design purposes requires the use of extensometers to measure the gauge length of the specimen. Data for research or quality-control purposes may use the change in distance between the grips (nominal extension).
Flexural creep may vary significantly with differences in specimen preparation and dimensions and in the test environment. The thermal history of the test specimen can also have profound effects on its creep behaviour (see Annex A). Consequently, when precise comparative results are required, these factors must be carefully controlled.
If flexural-creep properties are to be used for engineering-design purposes, the plastics materials should be tested over a broad range of stresses, times and environmental conditions.
The method may not be suitable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1, Cellular plastics, rigid -- Flexural tests -- Part 1: Bending test, and ISO 1209-2, Cellular plastics, rigid -- Flexural tests -- Part 2: Determination of flexural properties).
| DevelopmentNote |
Supersedes ISO 6602 and ISO 899 (04/2001) Supersedes ISO/DIS 899-2. (06/2003)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNI EN ISO 899-2:2015 | Identical |
| UNE-EN ISO 899-2:2003 | Identical |
| NBN EN ISO 899-2 : 2003 AMD 1 2015 | Identical |
| NEN EN ISO 899-2 : 2003 AMD 1 2015 | Identical |
| NS EN ISO 899-2 : 2003 AMD 1 2015 | Identical |
| I.S. EN ISO 899-2:2003 | Identical |
| PN EN ISO 899-2 : 2005 AMD 1 2015 | Identical |
| SN EN ISO 899-2 : 2003 AMD 1 2015 | Identical |
| UNI EN ISO 899-2 : 2006 | Identical |
| NF EN ISO 899-2:2003 | Identical |
| NEN-EN-ISO 899-2:2003 en | Identical |
| PN-EN ISO 899-2:2005 | Identical |
| SS-EN ISO 899-2:2003 | Identical |
| SN EN ISO 899-2:2003 | Identical |
| EN ISO 899-2:2003 | Identical |
| BS EN ISO 899-2 : 2003 | Identical |
| EN ISO 899-2:2003/A1:2015 | Identical |
| NF EN ISO 899-2 : 2003 AMD 1 2015 | Identical |
| DIN EN ISO 899-2:2015-06 | Identical |
| BS EN ISO 899-2:2003+A1:2015 | Identical |
| BS 2782-3.324B(1997) : 1997 | Identical |
| I.S. EN 13121-3:2016 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP |
| 10/30211370 DC : DRAFT JUNE 2010 | BS ISO 11833-1 - PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM |
| 13/30263803 DC : 0 | BS ISO 17296-4 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 4: DATA PROCESSING |
| BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
| 16/30329416 DC : 0 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| UNI EN ISO 11296-4 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| BS EN 16153 : 2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| I.S. EN ISO 11833-1:2012 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| I.S. EN 12566-3:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| BS EN ISO 3167:2014 | Plastics. Multipurpose test specimens |
| CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
| EN 12566-3:2016 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| EN 13121-3:2016 | GRP tanks and vessels for use above ground - Part 3: Design and workmanship |
| ISO 16616:2015 | Test methods for natural fibre-reinforced plastic composite (NFC) deck boards |
| 17/30345075 DC : 0 | BS EN ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| 05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
| 17/30360679 DC : DRAFT SEP 2017 | BS EN 17152-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND CONVEYANCE AND STORAGE OF NON-POTABLE WATER - BOXES USED FOR INFILTRATION, ATTENUATION AND STORAGE SYSTEMS - PART 1: SPECIFICATIONS FOR STORM WATER BOXES MADE OF PP AND PVC |
| BS ISO 12891-2:2014 | Retrieval and analysis of surgical implants Analysis of retrieved surgical implants |
| DD CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products |
| ISO 12891-2:2014 | Retrieval and analysis of surgical implants Part 2: Analysis of retrieved surgical implants |
| NF EN ISO 11296-4 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| UNI EN ISO 11833-1 : 2012 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM |
| EN ISO 11296-4:2018 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018) |
| BS EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with cured-in-place pipes |
| BS EN 1778:2000 | Characteristic values for welded thermoplastics constructions. Determination of allowable stresses and moduli for design of thermoplastics equipment |
| DIN EN ISO 11833-1:2012-11 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| I.S. EN ISO 3167:2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| DIN EN 13121-3:2016-10 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP |
| 14/30298583 DC : 0 | BS EN 13121-3 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP |
| I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| DIN EN 16153:2015-05 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 13121-3:2016 | GRP tanks and vessels for use above ground Design and workmanship |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 11296-4:2018 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes |
| UNE-EN 13121-3:2017 | GRP tanks and vessels for use above ground - Part 3: Design and workmanship |
| BS EN ISO 20753:2014 | Plastics. Test specimens |
| ISO 11833-1:2012 | Plastics Unplasticized poly(vinyl chloride) sheets Types, dimensions and characteristics Part 1: Sheets of thickness not less than 1 mm |
| UNE-EN ISO 11833-1:2012 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012) |
| UNI EN ISO 3167 : 2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS |
| BS ISO 16616:2015 | Test methods for natural fibre-reinforced plastic composite (NFC) deck boards |
| ONORM EN ISO 11833-1 : 2012 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| DD CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) Characterisation of WPC materials |
| 13/30242622 DC : 0 | BS ISO 12891-2 - RETRIEVAL AND ANALYSIS OF SURGICAL IMPLANTS - PART 2: ANALYSIS OF RETRIEVED SURGICAL IMPLANTS |
| I.S. EN ISO 11296-4:2018 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES (ISO 11296-4:2018) |
| UNE-EN ISO 11296-4:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2009, corrected version 2010-06-01) |
| UNI EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS |
| PREN ISO 11833-1 : DRAFT 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| S.R. CEN/TS 15534-2:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 2: CHARACTERISATION OF WPC MATERIALS |
| DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| UNE-EN 12566-3:2017 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| BS EN 12566-3 : 2005 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| BS EN ISO 11833-1:2012 | Plastics. Unplasticized poly(vinyl chloride) sheets. Types, dimensions and characteristics Sheets of thickness not less than 1 mm |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| UNE-EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| EN 16153:2013+A1:2015 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| EN 1778:1999 | Characteristic values for welded thermoplastics constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment |
| EN ISO 11833-1:2012 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012) |
| 13/30238193 DC : DRAFT DEC 2013 | BS ISO 16616 - TEST METHODS FOR NATURAL FIBER-REINFORCED PLASTIC COMPOSITE (NFC) DECK BOARDS |
| 06/30130317 DC : DRAFT JULY 2006 | ISO 11833-1 - PLASTICS - UNPLASTICIZED POLY (VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| 08/30174008 DC : DRAFT JUNE 2008 | BS ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACES PIPES |
| 13/30271610 DC : 0 | BS ISO 17296-3 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 3: TEST METHODS |
| 04/30046221 DC : 0 | PREN 13121-3 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP |
| BS ISO 11833-1:1998 | Plastics. Unplasticized poly(vinyl chloride) sheets. Tapes, dimensions and characteristics Sheets of thickness not less than 1 mm |
| DIN EN ISO 11296-4:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| I.S. EN 16153:2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
| S.R. CEN TS 15534-1:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials |
| UNE-EN 16153:2013 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
| EN ISO 178:2010/A1:2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
| ISO 472:2013 | Plastics Vocabulary |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 62:2008 | Plastics Determination of water absorption |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| ISO 178:2010 | Plastics Determination of flexural properties |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
$180.92
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF 1 User - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
Hardcopy - French
PDF 1 User - French
PDF 3 Users - French
PDF 5 Users - French
PDF 9 Users - French
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.