Name: ONORM EN 1218-5 : 2010
Brand: ON

ONORM EN 1218-5 : 2010

Superseded

SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN

Superseded date

21-10-2021

Published date

12-01-2013

Publisher

Osterreichisches Normungsinstitut/Austrian Standards

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
  3.1 General
  3.2 Terms
  3.3 Definitions
4 List of significant hazards
5 Safety requirements and/or measures
  5.1 General
  5.2 Controls
      5.2.1 Safety and reliability of control systems
      5.2.2 Position of controls
      5.2.3 Starting
      5.2.4 Normal stopping
      5.2.5 Emergency stop
      5.2.6 Integrated feed
      5.2.7 Positioning of tool spindles
      5.2.8 Speed changing
      5.2.9 Failure of the power supply
      5.2.10 Failure of control circuits
  5.3 Protection against mechanical hazards
      5.3.1 Stability
      5.3.2 Hazard resulting from break-up
      5.3.3 Tool holder and tool design
      5.3.4 Braking
      5.3.5 Devices to minimise the possibility or the effect
             of ejection
      5.3.6 Work-piece supports and guides
      5.3.7 Prevention of access to moving parts
  5.4 Protection against non-mechanical hazards
      5.4.1 Fire
      5.4.2 Noise
      5.4.3 Emission of chips and dust
      5.4.4 Electricity
      5.4.5 Ergonomics and handling
      5.4.6 Lighting
      5.4.7 Pneumatics
      5.4.8 Hydraulics
      5.4.9 Radiation
      5.4.10 Static electricity
      5.4.11 Errors of fitting
      5.4.12 Isolation
      5.4.13 Maintenance
6 Information for use
  6.1 Warning devices
  6.2 Marking
  6.3 Instruction handbook
Annex A (informative) Examples of safety related electronic
        control systems
Annex B (normative) Tool spindle dimensional tolerances
Annex C (normative) Operating conditions for noise emission
        measurement
      C.1 General
      C.2 Noise measurements
          C.2.1 Test conditions
          C.2.2 Microphone positions
          C.2.3 General data sheet
Annex D (informative) Safe working practice
Annexe ZA (informative) Relationship of this document with
          EC Directives
Bibliography

Specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to one side profiling machines with fixed table and feed rollers or feed chain hereinafter referred to as "machines", where the loading and unloading is manual and where the maximum work-piece height capacity is 200 mm.

DocumentType	Standard
PublisherName	Osterreichisches Normungsinstitut/Austrian Standards
Status	Superseded
SupersededBy	ÖNORM EN ISO 19085-12:2021 10 15

Standards	Relationship
UNI EN 1218-5 : 2010	Identical
NEN EN 1218-5 : 2004 + A1 2009	Identical
SN EN 1218-5 : 2004 + A1 2010	Identical
BS EN 1218-5 : 2004	Identical
DIN EN 1218-5:2010-02	Identical
I.S. EN 1218-5:2004	Identical
NF EN 1218-5 : 2004 + A1 2010	Identical
EN 1218-5:2004+A1:2009	Identical
UNE-EN 1218-5:2005	Identical
NBN EN 1218-5 : 2004 + A1 2009	Identical
NS EN 1218-5 : 2004 + A1 2009	Identical

ONORM EN ISO 3743-2 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
ISO 11202:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 3744:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO 354:2003	Acoustics — Measurement of sound absorption in a reverberation room
ISO/TR 11688-1:1995	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 3743-2:1994	Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
ONORM EN 1837 : 2009	SAFETY OF MACHINERY - INTEGRAL LIGHTING OF MACHINES
ISO 9614-1:1993	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
ONORM EN ISO 13849-1 : 2016	SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN (ISO 13849-1:2015)
ONORM EN ISO 11204 : AUG 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
ISO 3746:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
ISO 12100-2:2003	Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 12100-1:2003	Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015	Safety of machinery Emergency stop function Principles for design
ISO 3745:2012	Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
ISO 13849-1:2015	Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO 11204:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
ONORM EN ISO 11202 : 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
ISO 3743-1:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room