Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ONORM EN 877 : 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
Superseded date

28-04-2022

Published date

12-01-2013

Foreword
1 Scope
2 Normative References
3 Definitions
4 Technical Requirements
      4.1 General
      4.2 Dimensions
      4.3 Interconnection
      4.4 Mass
      4.5 Material characteristics of pipes, fittings
             and accessories
      4.6 Coatings for pipes, fittings and accessories
      4.7 Joints
      4.8 Buried systems
      4.9 Rainwater systems installed outside buildings
      4.10 Marking
5 Test Methods
      5.1 Surface condition
      5.2 Dimensions
      5.3 Mass
      5.4 Tensile strength of pipes and fittings
      5.5 Brinell hardness
      5.6 Ring crush test for grey cast iron pipes
      5.7 Coatings
      5.8 Joints
      5.9 Buried systems
      5.10 Rainwater systems installed outside buildings
      5.11 Marking
Annex A (informative) Other dimensions for buried systems
Annex B (informative) Other dimensions for rainwater systems
                      to be installed outside buildings
Annex C (informative) Field of use for buried pipes and
                      fittings, characteristics of soils,
                      load-bearing capacity
Annex D (informative) Information on manufacturing criteria
                      and quality assurance
Annex E (informative) Surveillance by an accredited third
                      party (certification by third party)
Annex F (informative) General information on some product
                      characteristics
Annex NZ (informative) National annex

Defines cast iron pipeline components used for the construction of discharge systems for drains and building normally as gravity systems. The range is from DN 40 to DN 600 inclusive. Covers requirements for the dimensions and tolerances, appearance, materials, mechanical properties, standard coatings for cast iron pipes, fittings and accessories.

DocumentType
Standard
PublisherName
Osterreichisches Normungsinstitut/Austrian Standards
Status
Superseded
SupersededBy

ISO 7724-1:1984 Paints and varnishes Colorimetry Part 1: Principles
EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
EN 605 : 1992 PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
ISO 2808:2007 Paints and varnishes Determination of film thickness
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
EN 476:2011 General requirements for components used in drains and sewers
ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 10204:2004 Metallic products - Types of inspection documents
ISO 185:2005 Grey cast irons Classification
EN 10003-1 : 1994 METALLIC MATERIALS - BRINELL HARDNESS TEST - TEST METHOD
EN ISO 1716:2010 Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010)
EN ISO 11925-2:2010/AC:2011 REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
ISO 4628-2:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more