PREN 1254-6 : DRAFT 2011

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You have already added this standard to your Watchlist.
Visit My Watchlist to view the full list.

COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS

Available format(s):

Superseded date: 01-10-2012

Language(s):

Published date: 12-01-2013

Publisher: Comite Europeen de Normalisation

Add to Watchlist

Pure ENs are not available for sale, please purchase a suitable national adoption

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Terms and Definitions
4 Operating temperatures and pressures
5 Requirements
6 Testing, assessment and sampling methods
7 Evaluation of conformity
8 Classification and designation
9 Marking
Annex A (normative) - Method for testing leaktightness
        of joints with metallic tube under internal
        hydrostatic pressure
Annex B (normative) - Method for testing resistance to
        pull-out of joints with metallic tube
Annex C (normative) - Test method for resistance of
        joints with metallic tube to temperature cycling
Annex D (normative) - Method for testing the resistance
        of joints with metallic tube to pressure
        cycling
Annex E (normative) - Test method for leaktightness
        of joints with metallic tube under vacuum
Annex F (normative) - Test method for the resistance
        of joints with metallic tube to vibration
Annex G (normative) - Test method for leaktightness
        of joints with metallic tube under internal
        hydrostatic pressure while subjected to
        bending
Annex H (normative) - Test method for disconnection
        and re-use
Annex I (normative) - Fitting rotation test
Annex J (normative) - Determination of resistance to
        stress corrosion
Annex K (normative) - Pressure test for fittings bodies
        with as-cast microstructure or fabricated by
        welding or brazing
Annex L (normative) - Determination of mean depth
        of dezincification
Bibliography

Abstract - (Show below) - (Hide below)

Describes materials and test requirements for fittings of copper and copper alloys.

General Product Information - (Show below) - (Hide below)

Comment Closes On
Committee	TC 133
Document Type	Draft
ISBN
Pages
Published
Publisher	Comite Europeen de Normalisation
Status	Superseded
Superseded By	EN 1254-6:2012

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
11/30213587 DC : 0	Identical
04/30095586 DC : 0	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

PREN 13618 : DRAFT 2009	FLEXIBLE HOSE ASSEMBLIES IN DRINKING WATER INSTALLATIONS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
09/30198696 DC : 0	BS EN 13618 - FLEXIBLE HOSE ASSEMBLIES IN DRINKING WATER INSTALLATIONS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
07/30163621 DC : 0	BS EN 1254-5 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 5: FITTINGS WITH SHORT ENDS FOR CAPILLARY BRAZING TO COPPER TUBES
07/30163615 DC : 0	BS EN 1254-1 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 1: FITTINGS WITH ENDS FOR CAPILLARY SOLDERING OR CAPILLARY BRAZING TO COPPER TUBES
07/30163618 DC : 0	BS EN 1254-2 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 2: FITTINGS WITH COMPRESSION ENDS FOR USE WITH COPPER TUBES
07/30144895 DC : 0	BS EN 723 - COPPER AND COPPER ALLOYS - COMBUSTION METHOD FOR DETERMINATION OF CARBON CONTENT ON THE INNER SURFACE OF COPPER TUBES OR FITTINGS
04/30114458 DC : 0	EN 14905 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - RECOMMENDED PRACTICE FOR THE INSTALLATION OF COPPER AND COPPER ALLOY PLUMBING FITTINGS

Standards Referencing This Book - (Show below) - (Hide below)

EN 1655:1997	Copper and copper alloys - Declarations of conformity
EN ISO 15875-2:2003/A1:2007	PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES
EN 1254-4:1998/AC:1999	COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 4: FITTINGS COMBINING OTHER END CONNECTIONS WITH CAPILLARY OR COMPRESSION ENDS
EN 12293:1999	Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling
EN 681-1:1996/A3:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN ISO 15874-5:2013	Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013)
EN 1057:2006+A1:2010	Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN ISO 15876-2:2017	Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017)
ISO 15875-5:2003	Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system
ISO 15875-2:2003	Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes
EN ISO 15876-5:2017	Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)
EN ISO 21003-2:2008/A1:2011	Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
EN 12449:2016	Copper and copper alloys - Seamless, round tubes for general purposes
EN 713:1993	Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
EN ISO 15875-5:2003	Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003)
EN ISO 9001:2015	Quality management systems - Requirements (ISO 9001:2015)
ISO 21003-2:2008	Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
ISO 6509:1981	Corrosion of metals and alloys Determination of dezincification resistance of brass
ISO 15876-2:2017	Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes
ISO 9001:2015	Quality management systems — Requirements
EN 12164:2016	Copper and copper alloys - Rod for free machining purposes
EN 12295:1999	Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling
ISO 9924-1:2016	Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers
EN ISO 21003-5:2008	Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)
EN 12294:1999	Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum
EN ISO 15874-2:2013	Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
EN ISO 6509 : 1995	CORROSION OF METALS AND ALLOYS - DETERMINATION OF DEZINCIFICATION RESISTANCE OF BRASS
EN 12165:2016	COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 15876-5:2017	Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system
EN 1982:2017	Copper and copper alloys - Ingots and castings
ISO 6957:1988	Copper alloys Ammonia test for stress corrosion resistance
EN 712:1993	Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart