Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

PREN 16129 : DRAFT 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 100 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES
Superseded date

01-06-2013

Published date

12-01-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Types of regulating devices
5 Constructional characteristics
6 Performance characteristics
7 Test methods
8 Marking, packaging, instructions
Annex A (normative) - Special requirements for devices
        fitted with pressure or flow rate operated
        safety functions
Annex B (normative) - Special requirements for devices
        fitted with a thermal shut off system
Annex C (normative) - Special requirements for devices
        under extreme temperature conditions
        (temperatures below -20 Degree C)
Annex D (normative) - Regulating devices for LPG
        cylinders to supply appliances installed in
        caravans and motor caravans or freshwater boats
Annex E (normative) - Complementary test requirements
        for non metallic thermoplastic or thermal setting
        materials used in the construction of devices
Annex F (normative) - Requirements for elastomeric
        reinforced diaphragms
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (informative) - Test method for resistance to
        corrosion
Annex J (normative) - Method for measuring leaks at
        test pressures less than or equal to 16 bar
Annex K (normative) - Special requirements for low
        pressure fixed regulators fitted with two or
        three outlets for outdoor use
Annex L (normative) - Special requirements for regulators
        fitted with an inlet valve
Annex M (Normative) - Devices for LPG cylinders to supply
        appliances installed in seawater boats
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 90/396/EEC
Bibliography

Describes the constructional and operational characteristics, the safety requirements, test methods and the marking of regulators and automatic change-over devices having a maximum regulated pressure of 4 bar, with a maximum capacity of 100 kg/h, for use with butane, propane and their mixtures in the vapour phase.

Committee
TC 181
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
NF EN 16129 : 2013 Identical
10/30228056 DC : 0 Identical

UNI/TR 11426 : 2011 USE OF LPG PLANTS NOT FED BY A DISTRIBUTION NETWORK AT TEMPORARY OUTDOOR EVENTS - DESIGN, INSTALLATION, MAINTENANCE AND OPERATION

EN 15202:2012 LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
EN 10226-2:2005 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN ISO 4892-3:2016 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
EN 13878 : 2003 LEISURE ACCOMMODATION VEHICLES - TERMS AND DEFINITIONS
EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
EN 12420:2014 Copper and copper alloys - Forgings
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 301:2006 Zinc alloy ingots intended for castings
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 178:2010 Plastics Determination of flexural properties
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
1990/396/EEC : 1990 COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more