We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • SAE AIR 851 : 2014

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    O-RING TENSION TESTING CALCULATIONS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  06-05-2014

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. CALCULATIONS
    4. EXAMPLE
    5. COMMENTS

    Abstract - (Show below) - (Hide below)

    This document is intended to facilitate calculation of O-Ring tension testing values.

    General Product Information - (Show below) - (Hide below)

    Committee AMS CE
    Document Type Standard
    Product Note STABILIZED VERSION IS NOW AVAILABLE
    Publisher SAE International
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE AMS 7254 : 2014 PERFLUOROETHER ELASTOMER
    SAE AMS 7264 : 2007 RINGS, SEALING, SILICONE RUBBER, HIGH TEMPERATURE RESISTANT, LOW COMPRESSION SET, 65 - 75
    SAE AMS7338A : 2013 RUBBER: BUTYL (IIR ABBREVIATION), PHOSPHATE ESTER RESISTANT, 65 TO 75 HARDNESS, FOR SEALS IN HYDRAULIC SYSTEMS, ETC.
    SAE AMS 7274 : 2014 RUBBER: BUTADIENE-ACRYLONITRILE (NBR), 65 TO 75 HARDNESS, FOR ELASTOMERIC SEALS IN AIRCRAFT ENGINE OIL SYSTEMS
    SAE AMS 7257 : 2014 PERFLUOROCARBON (FFKM) ENGINE OIL, FUEL AND HYDRAULIC FLUID RESISTANT 70 TO 80 HARDNESS FOR HIGH TEMPERATURE SEALS IN ENGINE OIL SYSTEMS, FUEL SYSTEMS AND HYDRAULIC SYSTEMS
    SAE AMS 7262 : C2001 RINGS, SEALING, ETHYLENE PROPYLENE (EPM) RUBBER, PHOSPHATE ESTER HYDRAULIC FLUID RESISTANT, 85-95
    SAE AMS 7259 : 2013 RUBBER: FLOUROCARBON (FKM), HIGH TEMPERATURE/FLUID RESISTANT, LOW COMPRESSION SET/85 TO 95 HARDNESS, FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS
    SAE AMS 7284 : 2016 RINGS, SEALING, PHOSPHONITRILIC FLUOROELASTOMER (FZ) AVIATION FUEL RESISTANT
    SAE AMS 7255 : 2014 RINGS, SEALING, TETRAFLUOROETHYLENE/PROPYLENE RUBBER (FEPM) HYDRAULIC FLUID AND SYNTHETIC OIL RESISTANT 70 TO 80
    SAE AMS 7266 : 2001 RINGS, SEALING, FLUOROCARBON RUBBER, GENERAL PURPOSE, HIGH TEMPERATURE, FUEL AND OIL RESISTANT 65 - 75
    SAE AMS 7258 : 2001 RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL RESISTANT, LOW SHRINKAGE 65-75
    SAE AMS 7272 : 2013 RUBBER: BUTADIENE-ACRYLONITRILE (NBR) SYNTHETIC LUBRICANT RESISTANT 65 - 75 HARDNESS FOR SEALS IN SYNTHETIC LUBRICANT SYSTEMS
    SAE AMS 7265 : 2001 RINGS, SEALING, ETHYLENE PROPYLENE RUBBER, PHOSPHATE ESTER HYDRAULIC FLUID RESISTANT, 75-85
    SAE AMS 7269 : 2003 RINGS, SEALING, SILICONE (PVMQ) RUBBER - LOW OUTGASSING, SPACE AND VACUUM SERVICE, 45-55
    SAE AMS 7256 : 2014 RINGS, SEALING, TETRAFLUOROETHYLENE/PROPYLENE RUBBER (FEPM) HYDRAULIC FLUID AND SYNTHETIC OIL RESISTANT 85 TO 95
    SAE AMS 7267 : 2001 RINGS, SEALING, SILICONE (VSI) RUBBER, HEAT RESISTANT, LOW COMPRESSION SET, 70-80
    SAE AMS 7268 : 2001 RINGS, SEALING-SILICONE RUBBER LOW COMPRESSION SET, NON-OIL RESISTANT 65 - 75
    SAE AMS 7287 : 2012 FLUOROCARBON ELASTOMER (FKM) HIGH TEMPERATURE/HTS OIL RESISTANT/FUEL RESISTANT LOW COMPRESSION SET/70 TO 80 HARDNESS, LOW TEMPERATURE TG -22 DEGREES F (-30 DEGREES C) FOR SEALS IN OIL/FUEL/SPECIFIC HYDRAULIC SYSTEMS
    SAE AMS 7260 : 2001 RINGS, BUTADIENE-ACRYLONITRILE (NBR) RUBBER, MOLDED FUEL AND LOW TEMPERATURE RESISTANT 70 - 80
    SAE AMS 7261 : D2001 RINGS, SEALING, PHOSPHONITRILIC (FZ) FLUOROELASTOMER, HIGH-TEMPERATURE-FLUID-RESISTANT

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1414 : 2015 : REDLINE Standard Test Methods for Rubber O-Rings
    SAE AS 568 : 2014 AEROSPACE SIZE STANDARD FOR O-RINGS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective