SAE AMS 1424 : 2017

Superseded

View Superseded by

FLUID, AIRCRAFT DEICING/ANTI-ICING, SAE TYPE 1

Available format(s)

Hardcopy , PDF

Superseded date

06-10-2018

Language(s)

English

Published date

01-01-2017

Publisher

SAE International

1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
APPENDIX A - ENVIRONMENTAL REQUIREMENTS AND TEST METHODS

Describes a deicing/anti-icing material in the form of a fluid.

Committee	G-12ADF
DevelopmentNote	Supersedes MIL A 8243. (06/2004) Supersedes SAE AS 8243. (04/2010) Supersedes SAE AMS 1425. (06/2010) Supersedes SAE AMS 1427. (07/2010)
DocumentType	Standard
Pages	17
PublisherName	SAE International
Status	Superseded
SupersededBy	SAE AMS 1424P : 2018
Supersedes	SAE AMS 1424 : 2016

SAE AMS 4049 : 2016	ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 2475H : 2009	PROTECTIVE TREATMENTS, MAGNESIUM ALLOYS
ASTM D 1177 : 2017 : REDLINE	Standard Test Method for Freezing Point of Aqueous Engine Coolants
SAE AMS 5886 : 2014	ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 50NI - 20CR - 20CO - 5.8MO - 2.2TI - 0.45AL CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 2100 DEGREES F (1149 DEGREES C) SOLUTION HEAT TREATED
SAE AMS 4911 : 2014	TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED
SAE AMS 4376 : 2011(R2018)	PLATE, MAGNESIUM ALLOY - 3.0AL - 1.0ZN - 0.20MN (AZ31B-H26) COLD ROLLED AND PARTIALLY ANNEALED
SAE AMS 4037 : 2014	ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED
SAE AIR 5567A : 2015	TEST METHOD FOR CATALYTIC CARBON BRAKE DISK OXIDATION
CFR 40(PTS790-999) : JUL 2017	PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY
MIL-STD-870 Revision C:2007	Cadmium Plating, Low Embrittlement, Electrodepositon
ASTM E 70	TEST METHOD FOR PH OF AQUEOUS SOLUTIONS WITH THE GLASS ELECTRODE
ASTM D 1331 : 2014 : REDLINE	Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials
SAE AMS P 83310 : 2016	PLASTIC SHEET, POLYCARBONATE, TRANSPARENT
SAE AS 5900 : 2016	STANDARD TEST METHOD FOR AERODYNAMIC ACCEPTANCE OF AMS1424 AND AMS1428 AIRCRAFT DEICING/ANTI-ICING FLUIDS
SAE ARP 1917 : 2002	CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS
SAE AS 6285 : 2016	AIRCRAFT GROUND DEICING/ANTI-ICING PROCESSES
SAE AMS 1424/1 : 2016	DEICING/ANTI-ICING FLUID, AIRCRAFT SAE TYPE 1 GLYCOL (CONVENTIONAL AND NON-CONVENTIONAL) BASED
ASTM D 93 : 2016-07	TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
MIL-PRF-25690 Revision B:1993	PLASTIC, SHEET AND FORMED PARTS, MODIFIED ACRYLIC BASE, MONOLITHIC, CRACK PROPAGATION RESISTANT
SAE AMS 4916 : 2014	TITANIUM ALLOY SHEET, STRIP, AND PLATE 8AL - 1MO - 1V DUPLEX ANNEALED
CFR 40(PTS136-149) : JUL 2017	PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY
SAE AS 5901 : 2014	WATER SPRAY AND HIGH HUMIDITY ENDURANCE TEST METHODS FOR SAE AMS1424 AND SAE AMS1428 AIRCRAFT DEICING/ANTI-ICING FLUIDS
SAE AMS 2470 : 2013	ANODIC TREATMENT OF ALUMINUM ALLOYS, CHROMIC ACID PROCESS
SAE AMS 1424/2 : 2016	DEICING/ANTI-ICING FLUID, AIRCRAFT SAE TYPE 1 NON-GLYCOL BASED
SAE AMS 5045 : 2015	STEEL, SHEET AND STRIP, 0.25 CARBON, MAXIMUM HARD TEMPER