SAE AMS 1435 : 2012

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You have already added this standard to your Watchlist.
Visit My Watchlist to view the full list.

FLUID, GENERIC, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS

Available format(s):

Superseded date: 06-11-2018

Language(s):

Published date: 01-01-2012

Publisher: SAE International

Add to Watchlist

Table of Contents - (Show below) - (Hide below)

1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
APPENDIX A

Abstract - (Show below) - (Hide below)

Describes deicing and anti-icing materials in the form of a fluid.

General Product Information - (Show below) - (Hide below)

Committee	G-12
Development Note	SUPERSEDES SAE AMS 1432. (07/1999) Supersedes SAE AMS 1426. (10/2016)
Document Type	Standard
ISBN
Pages
Published
Publisher	SAE International
Status	Superseded
Superseded By	SAE AMS 1435 D : 2018
Supersedes	SAE AMS 1432 : 1995 SAE AMS 1435 : 2010 SAE AMS 1426 : 2016

Standards Referenced By This Book - (Show below) - (Hide below)

SAE AIR 6170 : 2017	ICE MELTING TEST METHOD FOR RUNWAYS AND TAXIWAYS DEICING/ANTI-ICING CHEMICALS
SAE AIR 6130 : 2017	CADMIUM PLATE CYCLIC CORROSION TEST
PREN 4860 P1 : 2018	AEROSPACE SERIES - ENVIRONMENTAL TESTING - TEST XB: ABRASION OF MARKINGS, LETTERINGS, SURFACES AND MATERIALS CAUSED BY RUBBING OF FINGERTIPS AND HANDS
SAE AIR 5567A : 2015	TEST METHOD FOR CATALYTIC CARBON BRAKE DISK OXIDATION
SAE ARP 4902 : 2018	DESIGN OF AIRCRAFT DEICING FACILITIES
SAE AIR 6172A : 2017	ICE UNDERCUTTING TEST METHOD FOR RUNWAYS AND TAXIWAYS DEICING/ANTI-ICING CHEMICALS
MIL-DTL-9129 Revision G:2014	DISCHARGERS, ELECTROSTATIC, GENERAL SPECIFICATION FOR
SAE AIR 6211 : 2017	ICE PENETRATION TEST METHOD FOR RUNWAYS AND TAXIWAYS DEICING/ANTI-ICING CHEMICALS
SAE AIR 5490 : 2016	CARBON BRAKE CONTAMINATION AND OXIDATION
SAE AIR 4004 : 2015	GUIDE FOR INSTALLATION OF ELECTRICAL WIRE AND CABLE ON AIRCRAFT LANDING GEAR

Standards Referencing This Book - (Show below) - (Hide below)

SAE AMS 4049 : 2016	ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 2475H : 2009	PROTECTIVE TREATMENTS, MAGNESIUM ALLOYS
ASTM D 1177 : 2017 : REDLINE	Standard Test Method for Freezing Point of Aqueous Engine Coolants
SAE AMS 4911 : 2014	TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED
SAE AMS 4376 : 2011(R2018)	PLATE, MAGNESIUM ALLOY - 3.0AL - 1.0ZN - 0.20MN (AZ31B-H26) COLD ROLLED AND PARTIALLY ANNEALED
MIL-STD-290 Revision H:2013	PACKAGING AND MARKING OF PETROLEUM AND RELATED PRODUCTS
SAE AMS 4037 : 2014	ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED
SAE AIR 5567A : 2015	TEST METHOD FOR CATALYTIC CARBON BRAKE DISK OXIDATION
CFR 40(PTS790-999) : JUL 2017	PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY
SAE ARP 1917 : 2002	CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS
ASTM D 93 : 2016-07	TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
MIL-PRF-25690 Revision B:1993	PLASTIC, SHEET AND FORMED PARTS, MODIFIED ACRYLIC BASE, MONOLITHIC, CRACK PROPAGATION RESISTANT
ISO 5725:1986	Precision of test methods Determination of repeatability and reproducibility for a standard test method by inter-laboratory tests
SAE AMS 2825 : 1987	MATERIAL SAFETY DATA SHEETS
SAE AIR 6130 : 2011	CADMIUM PLATE CYCLIC CORROSION TEST
MIL-P-83310 Base Document:1971	PLASTIC SHEET, POLYCARBONATE, TRANSPARENT
SAE AMS 2470 : 2013	ANODIC TREATMENT OF ALUMINUM ALLOYS, CHROMIC ACID PROCESS
SAE AMS 5045 : 2015	STEEL, SHEET AND STRIP, 0.25 CARBON, MAXIMUM HARD TEMPER

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart