SAE AMS 2817 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PACKAGING AND IDENTIFICATION OF MOLDED ELASTOMERIC SEALS AND SEALING COMPONENTS
Available format(s)
Hardcopy , PDF
Superseded date
24-02-2024
Language(s)
English
Published date
22-11-2016
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. STORAGE OF ELASTOMERIC ITEMS
7. ACKNOWLEDGMENT
8. NOTES
Specifies procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling/transportation/storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
| Committee |
AMS-CE
|
| DevelopmentNote |
Supersedes MIL P 4861 (C). (08/2007)
|
| DocumentType |
Revision
|
| Pages |
8
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| MIL-P-4861 Revision C:1991 | Similar to |
| SAE AIR 1412 : 2018 | DESIGNING FOR LONG LIFE WITH ELASTOMERS |
| SAE AMS 7254 : 2014 | PERFLUOROETHER ELASTOMER |
| NFPA T3.19.25 : 2004 : R2014 | INFORMATION REPORT - FLUID POWER SYSTEMS - SEALING DEVICES - STORAGE, HANDLING AND INSTALLATION OF ELASTOMERIC SEALS AND EXCLUSION DEVICES |
| SAE AS 6058 : 2016 | PACKING, PREFORMED, O-RING MOLDED FROM PERFLUOROETHER, FFO MATERIAL |
| SAE AMS 3332 : 2015 | SILICONE RUBBER, EXTREME LOW-TEMPERATURE RESISTANT, 15 - 30 |
| SAE AS 27195 : 2014 | SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-R-7362 |
| SAE AMS 7269 : 2003 | RINGS, SEALING, SILICONE (PVMQ) RUBBER - LOW OUTGASSING, SPACE AND VACUUM SERVICE, 45-55 |
| SAE AMS3353A:2023 | Elastomer: Fluorocarbon (FKM) Aircraft Engine Oil, Fuel and Hydraulic Fluid Resistant Low Temperature Sealing Tg -40 °F (-40 °C) / 70 to 80 Hardness, for Products in Aircraft Engine Oil, Fuel, and Hydraulics Systems |
| SAE AS 27197 : 2014 | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, SILICONE RUBBER, AMS7268 |
| SAE AS 27196 : 2014 | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROCARBON RUBBER, AMS7276 |
| MIL-DTL-24231 Revision E:2013 | Connectors, Plugs, Receptacles, Adapters, Hull Inserts, and Hull Insert Plugs, Pressure-Proof, General Specification for |
| SAE AMS 7284 : 2016 | RINGS, SEALING, PHOSPHONITRILIC FLUOROELASTOMER (FZ) AVIATION FUEL RESISTANT |
| SAE AMS 7272 : 2013 | RUBBER: BUTADIENE-ACRYLONITRILE (NBR) SYNTHETIC LUBRICANT RESISTANT 65 - 75 HARDNESS FOR SEALS IN SYNTHETIC LUBRICANT SYSTEMS |
| SAE ARP 5316 : 2014 | STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY |
| SAE AS 83461/2 : 2016 | STRAIGHT THREAD TUBE FITTING BOSS O-RING MOLDED FROM AMS-P-83461 RUBBER |
| SAE AMS P 5315 : 2013 | ACRYLONITRILE-BUTADIENE (NBR) RUBBER FOR FUEL-RESISTANT SEALS 60 TO 70 |
| SAE AS 5728 : 2016 | O-RING MOLDED FROM AMS7268 (SILICONE) MATERIAL |
| SAE AMS 7260 : 2001 | RINGS, BUTADIENE-ACRYLONITRILE (NBR) RUBBER, MOLDED FUEL AND LOW TEMPERATURE RESISTANT 70 - 80 |
| SAE AS 28778 : 2016 | O-RING, STRAIGHT THREAD TUBE FITTING BOSS MOLDED FROM AMS-P-5510 RUBBER |
| SAE AS 83248/1 : 2016 | O-RING MOLDED FROM AMS7276 MATERIAL |
| SAE AS 5316 : 2017 | STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY |
| SAE AS 27194C : 2014(S2018) | SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-P-5315 |
| SAE AMS R 7362 : 2012 | NITRILE RUBBER, SYNTHETIC, SOLID, SHEET, STRIP AND FABRICATED PARTS, SYNTHETIC OIL RESISTANT |
| SAE AMS 7255 : 2014 | RINGS, SEALING, TETRAFLUOROETHYLENE/PROPYLENE RUBBER (FEPM) HYDRAULIC FLUID AND SYNTHETIC OIL RESISTANT 70 TO 80 |
| SAE AS 29561 : 2015 | O-RING, SYNTHETIC LUBRICANT RESISTANT MOLDED FROM AMS-R-7362 RUBBER |
| SAE AS 6414 : 2017 | MANUFACTURING PROCESSING REQUIREMENTS FOR MOLDED ELASTOMER COMPONENTS USED IN AEROSPACE APPLICATIONS |
| SAE AS 28772 : 2015 | 'D' RING SEAL FOR SHOCK STRUTS MOLDED FROM AMS-P-25732 MATERIAL |
| API 20L : 1ED 2018 | QUALIFICATION OF POLYMERIC SEAL MANUFACTURERS FOR USE IN THE PETROLEUM AND NATURAL GAS INDUSTRIES |
| SAE AMS 7256 : 2014 | RINGS, SEALING, TETRAFLUOROETHYLENE/PROPYLENE RUBBER (FEPM) HYDRAULIC FLUID AND SYNTHETIC OIL RESISTANT 85 TO 95 |
| SAE AS 6203 : 2016 | O-RING, MOLDED FROM AMS7379 RUBBER FOR USE WITH AS5202 PORTS |
| SAE AMS 7267 : 2001 | RINGS, SEALING, SILICONE (VSI) RUBBER, HEAT RESISTANT, LOW COMPRESSION SET, 70-80 |
| SAE AS 708 : 2014 | TOP VISUAL QUALITY (TVQ) O-RING PACKINGS AND GASKETS - SURFACE INSPECTION GUIDE AND ACCEPTANCE STANDARD |
| SAE AMS 7261 : D2001 | RINGS, SEALING, PHOSPHONITRILIC (FZ) FLUOROELASTOMER, HIGH-TEMPERATURE-FLUID-RESISTANT |
| SAE AS 83461/1 : 2016 | M83461 O-RING MOLDED FROM AMS-P-83461 RUBBER |
| SAE AMS 7264 : 2007 | RINGS, SEALING, SILICONE RUBBER, HIGH TEMPERATURE RESISTANT, LOW COMPRESSION SET, 65 - 75 |
| SAE AMS7338A : 2013 | RUBBER: BUTYL (IIR ABBREVIATION), PHOSPHATE ESTER RESISTANT, 65 TO 75 HARDNESS, FOR SEALS IN HYDRAULIC SYSTEMS, ETC. |
| ISO 27996:2009 | Aerospace fluid systems — Elastomer seals — Storage and shelf life |
| SAE AMS P 5510 : 2013 | O-RING, PREFORMED, STRAIGHT THREAD TUBE FITTING BOSS, TYPE 1 HYDRAULIC (-65 TO 160 DEGREES F) |
| SAE AMS 7259 : 2013 | RUBBER: FLOUROCARBON (FKM), HIGH TEMPERATURE/FLUID RESISTANT, LOW COMPRESSION SET/85 TO 95 HARDNESS, FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
| SAE AS 5729 : 2016 | O-RING MOLDED FROM AMS7379 (FLUOROCARBON) MATERIAL |
| SAE AMS 7262 : C2001 | RINGS, SEALING, ETHYLENE PROPYLENE (EPM) RUBBER, PHOSPHATE ESTER HYDRAULIC FLUID RESISTANT, 85-95 |
| SAE AS 27198 : 2014 | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROSILICONE RUBBER, MIL-DTL-25988 |
| SAE AMS 7266 : 2001 | RINGS, SEALING, FLUOROCARBON RUBBER, GENERAL PURPOSE, HIGH TEMPERATURE, FUEL AND OIL RESISTANT 65 - 75 |
| NFPA T3.19.25 : 2004 | INFORMATION REPORT - FLUID POWER SYSTEMS - SEALING DEVICES - STORAGE, HANDLING AND INSTALLATION OF ELASTOMERIC SEALS AND EXCLUSION DEVICES |
| SAE AMS 7274 : 2014 | RUBBER: BUTADIENE-ACRYLONITRILE (NBR), 65 TO 75 HARDNESS, FOR ELASTOMERIC SEALS IN AIRCRAFT ENGINE OIL SYSTEMS |
| BS ISO 27996:2009 | Aerospace fluid systems. Elastomer seals. Storage and shelf life |
| 07/30155311 DC : 0 | BS ISO 27996 - AEROSPACE FLUID SYSTEMS - ELASTOMER SEALS - STORAGE AND SHELF LIFE |
| SAE AMS 7257 : 2014 | PERFLUOROCARBON (FFKM) ENGINE OIL, FUEL AND HYDRAULIC FLUID RESISTANT 70 TO 80 HARDNESS FOR HIGH TEMPERATURE SEALS IN ENGINE OIL SYSTEMS, FUEL SYSTEMS AND HYDRAULIC SYSTEMS |
| SAE AMS 7258 : 2001 | RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL RESISTANT, LOW SHRINKAGE 65-75 |
| SAE AS 83248/2 : 2016 | O-RING MOLDED FROM AMS7259 MATERIAL |
| SAE AS 29512 : 2016 | HYDROCARBON FUEL RESISTANT, TUBE FITTING, O-RING MOLDED FROM AMS-P-5315 RUBBER |
| SAE AS 83485 : 2016 | O-RING MOLDED FROM AMS7287 MATERIAL |
| SAE AMS 7287 : 2012 | FLUOROCARBON ELASTOMER (FKM) HIGH TEMPERATURE/HTS OIL RESISTANT/FUEL RESISTANT LOW COMPRESSION SET/70 TO 80 HARDNESS, LOW TEMPERATURE TG -22 DEGREES F (-30 DEGREES C) FOR SEALS IN OIL/FUEL/SPECIFIC HYDRAULIC SYSTEMS |
| SAE AS 29513 : 2016 | PACKING, PREFORMED, HYDROCARBON FUEL RESISTANT, 'O' RING |
| SAE AMS 7268 : 2001 | RINGS, SEALING-SILICONE RUBBER LOW COMPRESSION SET, NON-OIL RESISTANT 65 - 75 |
| NFPA T3.19.25 : 2004 : R2009 | INFORMATION REPORT - FLUID POWER SYSTEMS - SEALING DEVICES - STORAGE, HANDLING AND INSTALLATION OF ELASTOMERIC SEALS AND EXCLUSION DEVICES |
| SAE AS5729B:2023 | O-RING MOLDED FROM AMS7379 FLUOROCARBON (FKM) MATERIAL |
| SAE AIR1412E:2018(S2023) | Designing for Long Life with Elastomers(STABILIZED Jul 2023) |
| SAE AS 568 : 2014 | AEROSPACE SIZE STANDARD FOR O-RINGS |
| SAE ARP 5316 : 2014 | STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY |
| ASTM D 1418 : 2017 : REDLINE | Standard Practice for Rubber and Rubber Latices—Nomenclature |
$161.65
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.