SAE J 2551/1 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION
Superseded date
07-10-2019
Published date
01-01-2013
Publisher
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. SAFETY CONSIDERATIONS
5. TUBE SIZING, TUBE CONNECTION SELECTION, AND ROUTINGS
6. TUBE DESIGN, DIMENSIONING, TOLERANCES, AND INSPECTION
7. TUBE AND TUBE ASSEMBLY FABRICATION
8. TUBE CLEANLINESS
9. UNINTENDED USES
10. NOTES
Specifies general recommendations for designing and fabricating carbon, alloy and high strength low alloy steel tube assemblies for fluid power applications utilizing commonly available manufacturing methods and general guidelines for tube selection and application.
| DevelopmentNote |
Supersedes SAE J 2551. (02/2013)
|
| DocumentType |
Standard
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE J 2551/3 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT |
| SAE J 2435 : 2015 | WELDED FLASH CONTROLLED, SAE 1021 CARBON STEEL TUBING, NORMALIZED FOR COLD FORMING, WELDING AND BRAZING |
| SAE J 524 : 2016 | SEAMLESS LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| SAE J 525 : 2016 | WELDED AND COLD DRAWN LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| SAE J 2467 : 2020 | WELDED AND COLD-DRAWN, SAE 1021 CARBON STEEL TUBING NORMALIZED FOR BENDING AND FLARING |
| SAE J 1677 : 2016 | TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING |
| SAE J 2613 : 2017 | WELDED FLASH CONTROLLED, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, DOUBLE FLARING, COLD FORMING, WELDING, AND BRAZING |
| SAE J 2467 : 2015 | WELDED AND COLD-DRAWN, SAE 1021 CARBON STEEL TUBING NORMALIZED FOR BENDING AND FLARING |
| SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
| SAE J 2614 : 2018 | WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING |
| SAE J 2551/2 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS |
| SAE J 526 : 2016 | WELDED LOW-CARBON STEEL TUBING SUITABLE FOR BENDING, FLARING, BEADING, FORMING AND BRAZING |
| SAE J 533 : 2017 | FLARES FOR TUBING |
| ISO 272:1982 | Fasteners — Hexagon products — Widths across flats |
| ISO 16028:1999 | Hydraulic fluid power — Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) — Specifications |
| SAE J 836 : 1970 | AUTOMOTIVE METALLURGICAL JOINING |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| EN 10305-3:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
| SAE J 518 : 2013 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, FOUR-BOLT SPLIT FLANGE TYPE |
| SAE J 1926/3 : 2016 | CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ASME B1.1 THREADS AND O-RING SEALING - PART 3: LIGHT-DUTY (L-SERIES) STUD ENDS |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 4399:1995 | Fluid power systems and components Connectors and associated components Nominal pressures |
| ISO 10583:1993 | Aerospace fluid systems — Test methods for tube/fitting assemblies |
| ISO 6605:2017 | Hydraulic fluid power — Test methods for hoses and hose assemblies |
| ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
| ASTM A 519/A519M : 2017 : REDLINE | Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing |
| SAE J 1290 : 2012 | AUTOMOTIVE HYDRAULIC BRAKE SYSTEM - METRIC TUBE CONNECTIONS |
| SAE J 2832 : 2009 | WELDED FLASH CONTROLLED, HIGH STRENGTH (690 MPA TENSILE STRENGTH) LOW ALLOY STEEL HYDRAULIC TUBING, STRESS RELIEVED ANNEALED FOR BENDING AND DOUBLE FLARING |
| ISO 6150:1988 | Pneumatic fluid power Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 Mpa, and 2,5 MPa) Plug connecting dimensions, specifications, application guidelines and testing |
| SAE J 1453/2 : 2015 | Specification for O-Ring Face Seal Connectors: Part 2 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Braze-on Tube Ends, Caps, and Connectors with ISO 6149-2 Metric Stud Ends and ISO 6162 4-Bolt Flange Heads |
| SAE J 1273 : 2014 | RECOMMENDED PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES |
| SAE J 2592 : 2013 | CARBON STEEL TUBING FOR GENERAL USE - UNDERSTANDING NONDESTRUCTIVE TESTING FOR CARBON STEEL TUBING |
| SAE J 1231 : 2016 | FORMED TUBE ENDS FOR HOSE CONNECTIONS AND HOSE FITTINGS |
| EN 10305-2:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 2: Welded cold drawn tubes |
| ISO 3305:1985 | Plain end welded precision steel tubes — Technical conditions for delivery |
| SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
| SAE J 1926/1 : 2016 | CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ASME B1.1 THREADS AND O-RING SEALING - PART 1: THREADED PORT WITH O-RING SEAL IN TRUNCATED HOUSING |
| ISO 6162-2:2012 | Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76 |
| SAE J 356 : 2013 | WELDED FLASH-CONTROLLED LOW-CARBON STEEL TUBING NORMALIZED FOR BENDING, DOUBLE FLARING, AND BEADING |
| ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
| EN 10305-4:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
| SAE J 1453/3 : 2012 | SPECIFICATION FOR O-RING FACE SEAL CONNECTORS: PART 3 - REQUIREMENTS, DIMENSIONS, AND TESTS FOR STEEL UNIONS, BULKHEADS, SWIVELS, BRAZE SLEEVES, CAPS, AND CONNECTORS WITH SAE J1926-2 INCH STUD ENDS |
| ASTM D 2247 : 2015 : REDLINE | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ISO 6072:2011 | Rubber Compatibility between hydraulic fluids and standard elastomeric materials |
| SAE J 246 : 2012 | SPHERICAL AND FLANGED SLEEVE (COMPRESSION) TUBE FITTINGS |
| SAE J 2593 : 2015 | INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS |
| SAE J 343 : 2016 | TEST AND TEST PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES |
| SAE J 2614 : 2009 | WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING |
| SAE J 515 : 2015 | SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS |
| SAE J 1453/1 : 2012 | SPECIFICATION FOR O-RING FACE SEAL CONNECTORS - PART 1: TUBE CONNECTION DETAILS AND COMMON REQUIREMENTS FOR PERFORMANCE AND TESTS |
| ISO 8434-3:2005 | Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
| ISO 6162-1:2012 | Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| SAE J 2094 : 2001 | VEHICLE & CONTROL MODIFICATIONS FOR DRIVERS WITH PHYSICAL DISABILITIES - TERMINOLOGY |
| SAE J 2435 : 2015 | WELDED FLASH CONTROLLED, SAE 1021 CARBON STEEL TUBING, NORMALIZED FOR COLD FORMING, WELDING AND BRAZING |
| ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
| SAE J 514 : 2012 | HYDRAULIC TUBE FITTINGS |
| SAE J 526 : 2016 | WELDED LOW-CARBON STEEL TUBING SUITABLE FOR BENDING, FLARING, BEADING, FORMING AND BRAZING |
| ISO 3457:2003 | Earth-moving machinery Guards Definitions and requirements |
| ISO 6164:1994 | Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
| SAE J 527 : 2013 | BRAZED DOUBLE WALL LOW-CARBON STEEL TUBING |
| ISO 8434-4:1995 | Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples |
| ISO 3304:1985 | Plain end seamless precision steel tubes — Technical conditions for delivery |
| SAE J 525 : 2016 | WELDED AND COLD DRAWN LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| ISO 273:1979 | Fasteners — Clearance holes for bolts and screws |
| SAE J 1677 : 2016 | TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING |
| SAE J 524 : 2016 | SEAMLESS LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 10763:1994 | Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures |
| SAE J 2467 : 2015 | WELDED AND COLD-DRAWN, SAE 1021 CARBON STEEL TUBING NORMALIZED FOR BENDING AND FLARING |
| AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
| SAE J 2044 : 2009 | QUICK CONNECT COUPLING SPECIFICATION FOR LIQUID FUEL AND VAPOR/EMISSIONS SYSTEMS |
| ASTM A 554 : 2016 : REDLINE | Standard Specification for Welded Stainless Steel Mechanical Tubing |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| SAE J 1926/2 : 2016 | CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ASME B1.1 THREADS AND O-RING SEALING - PART 2: HEAVY-DUTY (S SERIES) STUD ENDS |
| SAE J 533 : 2017 | FLARES FOR TUBING |
| SAE J 2551/2 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS |
| ISO 2944:2000 | Fluid power systems and components — Nominal pressures |
| SAE J 2551/3 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
| SAE J512 : 1997 | AUTOMOTIVE TUBE FITTINGS |
| ISO 6149:1980 | Fluid power systems and components Metric ports Dimensions and design |
| ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) |
| SAE J 2613 : 2009 | WELDED FLASH CONTROLLED, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, DOUBLE FLARING, COLD FORMING, WELDING, AND BRAZING |
| SAE J 2833 : 2009 | WELDED AND COLD-DRAWN, HIGH STRENGTH (690 MPA TENSILE STRENGTH) LOW ALLOY STEEL HYDRAULIC TUBING, STRESS RELIEVED ANNEALED FOR BENDING AND FLARING |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.