Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • SAE J 2891 : 2015

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    AUXILIARY POWER UNIT ELECTRICAL INTERFACE REQUIREMENTS FOR CLASS EIGHT TRUCKS

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-05-2020

    Language(s):  English

    Published date:  31-12-2014

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. REFERENCES
    3. ABBREVIATIONS AND DEFINITIONS
    4. GENERAL APPLICATION CONSIDERATIONS
    5. ELECTRICAL PERFORMANCE
    6. OPERATING ENVIRONMENT
    7. ELECTROMAGNETIC CAPATIBILITY
    8. STANDARD SAFETY CONSIDERATIONS
    9. NOTES

    Abstract - (Show below) - (Hide below)

    This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE J 1773 : 2014 SAE ELECTRIC VEHICLE INDUCTIVELY COUPLED CHARGING
    UL 1699 : 3ED 2017 ARC-FAULT CIRCUIT-INTERRUPTERS
    SAE J 1939/15 : 2015 PHYSICAL LAYER, 250 KBPS, UN-SHIELDED TWISTED PAIR (UTP)
    SAE J 1113/13 : 2015 ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURE FOR VEHICLE COMPONENTS - PART 13: IMMUNITY TO ELECTROSTATIC DISCHARGE
    SAE J 1113/12 : 2006 ELECTRICAL INTERFERENCE BY CONDUCTION AND COUPLING - CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES
    SAE J 1673 : 2012 HIGH VOLTAGE AUTOMOTIVE WIRING ASSEMBLY DESIGN
    UL 943 : 5 GROUND-FAULT CIRCUIT-INTERRUPTERS
    SAE J 1128 : 2015 LOW VOLTAGE PRIMARY CABLE
    SAE J 1113/11 : 2012 IMMUNITY TO CONDUCTED TRANSIENTS ON POWER LEADS
    SAE J 1113/42 : 2010 ELECTROMAGNETIC COMPATIBILITY - COMPONENT TEST PROCEDURE - PART 42: CONDUCTED TRANSIENT EMISSIONS
    CISPR 25:2016 Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
    SAE J 1455 : 2017 RECOMMENDED ENVIRONMENTAL PRACTICES FOR ELECTRONIC EQUIPMENT DESIGN IN HEAVY-DUTY VEHICLE APPLICATIONS
    SAE J 1113/1 : 2013 ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURES AND LIMITS FOR COMPONENTS OF VEHICLES, BOATS (UP TO 15 M), AND MACHINES (EXCEPT AIRCRAFT) (16.6 HZ TO 18 GHZ)
    SAE J 2698 : 2014 PRIMARY SINGLE PHASE NOMINAL 120 VAC WIRING DISTRIBUTION ASSEMBLY DESIGN - TRUCK AND BUS
    NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
    SAE J 1127 : 2015 LOW VOLTAGE BATTERY CABLE
    CSA C22.2 No. 107.1 : 2016 POWER CONVERSION EQUIPMENT
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more