NUT, SELF LOCKING - UNS S66286, 425 DEGREE C AND 650 DEGREE C, 1100 MPA, MJ THREAD, PROCUREMENT SPECIFICATION FOR, METRIC

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-03-2018

Publisher

SAE International

1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION OF DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
APPENDIX A - MEASUREMENT OF PERPENDICULARITY
             VARIATION OF THE BEARING SURFACE
APPENDIX B - WRENCH TORQUE TEST
APPENDIX C - PUSH OUT TEST
APPENDIX D - TORQUE OUT TEST
APPENDIX E - PERMANENT SET TEST
APPENDIX F - REUSABILITY TEST AT ROOM TEMPERATURE,
             AFTER BAKING
APPENDIX G - REUSABILITY TEST AT ROOM TEMPERATURE,
             AS RECEIVED CONDITION
APPENDIX H - THREE CYCLES TEST AT ROOM TEMPERATURE
APPENDIX J - ACCEPTANCE CRITERIA OF SURFACE
             DISCONTINUITIES ON SELF LOCKING NUTS

Specifies the requirements for the following types of self locking nuts: wrenching nuts, i.e., hex, double hex, spline drive; and anchor nuts, i.e., plate nuts, gang channel nuts, shank (clinch) nuts.

Committee	E-25
DocumentType	Standard
Pages	41
PublisherName	SAE International
Status	Current
Supersedes	SAE MA 1568 : 2012

MIL L 7808 : K (1)	LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
SAE AMS 5737 : 2012	STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 2645 : 1995	FLUORESCENT PENETRANT INSPECTION
SAE AMS 5525 : 2012	STEEL, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND PLATE 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, 1800 DEGREE F (982 DEGREE C) SOLUTION HEAT TREATED
SAE MA 1586 : 2013	WRENCH CONFIGURATION, 12 SPLINE DRIVE, METRIC
SAE MA 3374 : 2012	BOLTS AND SCREWS, UNS S66286, CORROSION AND HEAT RESISTANT STEEL, PROCUREMENT SPECIFICATION, METRIC
ASME B46.1 : 2009	SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
SAE AMS 5734 : 2012	STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C) SOLUTION HEAT TREATED
NA 0012 : REV 2	FIXTURE, BEARING SURFACE SQUARENESS TEST, SELF-LOCKING NUTS, METRIC
SAE AMS 5732 : 2012	STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 2350 : 1989	STANDARDS AND TEST METHODS
SAE MA 1370 : 2012	SCREW THREADS - MJ PROFILE, METRIC
SAE AMS 5731 : 2012	STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED
SAE AMS 2411 : 2013	PLATING, SILVER FOR HIGH TEMPERATURE APPLICATIONS
MIL-STD-794 Revision E:1982	PART AND EQUIPMENT, PROCEDURES FOR PACKAGING AND PACKING OF
MA1520A : 2012(R2018)	AREAS FOR CALCULATING STRESS OR LOAD VALUES FOR METRIC MJ EXTERNALLY THREADED FASTENERS
MIL-STD-105 Revision E:1989	SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
SAE AS 1310 : 2012	FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF