SAE MA 1573 : 2016

Superseded

View Superseded by

NUT, SELF-LOCKING, STEEL, CLASS 1100 MPA/235 DEGREES C, MJ THREAD PROCUREMENT SPECIFICATION FOR, METRIC

Available format(s)

Hardcopy , PDF

Superseded date

31-12-2022

Language(s)

English

Published date

15-11-2016

Publisher

SAE International

1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGEMENT
7. REJECTIONS
8. NOTES
APPENDIX A - MEASUREMENT OF PERPENDICULARITY VARIATION OF THE
             BEARING SURFACE
APPENDIX B - WRENCH TORQUE TEST
APPENDIX C - PUSH-OUT TEST
APPENDIX D - TORQUE-OUT TEST
APPENDIX E - PERMANENT SET TEST
APPENDIX F - REUSABILITY TEST AT ROOM TEMPERATURE, AFTER BAKING
APPENDIX G - REUSABILITY TEST AT ROOM TEMPERATURE, AT RECEIVED
             CONDITION
APPENDIX H - THREE-CYCLE TEST AT ROOM TEMPERATURE
APPENDIX J - ACCEPTANCE CRITERIA OF SURFACE DISCONTINUITIES ON
             SELF-LOCKING NUTS

Describes the requirements for the following types of self-locking nuts: a. Wrenching nuts: that is, hex, double hex, spline drive b. Anchor nuts: that is, plate nuts, gang channel nuts, shank nuts.

Committee	E-25
DocumentType	Standard
Pages	39
PublisherName	SAE International
Status	Superseded
SupersededBy	SAE MA1573B:2011(S2021)
Supersedes	SAE MA 1573 : 2011

ISO 5855-2:1999	Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts
SAE MA 1586 : 2013	WRENCH CONFIGURATION, 12 SPLINE DRIVE, METRIC
SAE AMS 6322 : 2014	STEEL BARS, FORGINGS, AND RINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740)
MIL-PRF-7808 Revision L:1997	LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
MIL-STD-2073-1 Revision E:2008	STANDARD PRACTICE FOR MILITARY PACKAGING
ISO 965-2:1998	ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
SAE AMS 2759 : 2014	HEAT TREATMENT OF STEEL PARTS, GENERAL REQUIREMENTS
ASME B46.1 : 2009	SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
SAE AMS 5085 : 2017	STEEL SHEET, STRIP, AND PLATE, 0.48 - 0.55C (SAE 1050)
NASM1312:2012	FASTENER TEST METHODS METHOD 11 TENSION FATIGUE
NA 0012 : REV 2	FIXTURE, BEARING SURFACE SQUARENESS TEST, SELF-LOCKING NUTS, METRIC
SAE AMS 6304 : 2016	LOW-ALLOY STEEL, HEAT-RESISTANT, BARS, FORGINGS, AND TUBING, 0.95CR - 0.55MO - 0.30V (0.40 - 0.50C)
SAE AMS 6300 : 2015	STEEL BARS AND FORGINGS, 0.25MO (0.35 - 0.40C) (SAE 4037)
SAE AMS 2350 : 1989	STANDARDS AND TEST METHODS
NAM 1312/113 : REV 1	FASTENER TEST METHODS, METRIC METHOD 113 DOUBLE SHEAR TEST
SAE AMS 6351 : 2015	STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), SPHEROIDIZED
ASTM E 1444 : 2005	Standard Practice for Magnetic Particle Testing
MA1520A : 2012(R2018)	AREAS FOR CALCULATING STRESS OR LOAD VALUES FOR METRIC MJ EXTERNALLY THREADED FASTENERS
NAM 1312/105 : REV 1	FASTENER TEST METHODS METRIC METHOD 105 STRESS DURABILITY
SAE AMS 2400 : 2013	PLATING, CADMIUM
NAM 1312/108 : REV 1	FASTENER TEST METHODS, METRIC METHOD 108 TENSILE STRENGTH
SAE AMS 6350 : 2015	STEEL SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130)
SAE AMS 6370 : 2016	STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130)
NAM 1312/111 : REV 1	FASTENER TEST METHODS, METRIC METHOD 111 TENSION FATIGUE
NAM 1312/107 : REV 1	FASTENER TEST METHODS, METRIC METHOD 107 VIBRATION
SAE MA 3376 : 2012	BOLTS & SCREWS, UNS G87400 TENSILE STRENGTH 860 MPA & 1000 MPA PROCUREMENT SPECIFICATION, METRIC
SAE AS 1310 : 2012	FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF