MIL C 16173 : E
|
CORROSION PREVENTIVE COMPOUND, SOLVENT CUTBACK, COLD APPLICATION
|
SAE AMS 5737 : 2012
|
STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS AND TUBING, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED, 1650 DEGREES F (899 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
|
BS A 346:2000
|
UNJ threads. General requirements and limit dimensions
|
SBAC TS 21 : 2011
|
MANUFACTURING SPECIFICATION FOR BOLTS, 900 MPA (130,000 LBF/IN[2]) - TENSILE AT ROOM TEMPERATURE
|
DEF 2331 : A AMD 3
|
PROTECTIVE PX 1 DYED AND UNDYED
|
SAE AMS 7477 : B 70(R1982)
|
BOLTS AND SCREWS-STEEL-CORROSION AND HEAT RESISTANT, UPSET HEADED, HEAT TREATED, ROLL THREADED SOLUTION AND PRECIPITATION TREATED
|
ISO 2859:1974
|
Sampling procedures and tables for inspection by attributes
|
DEFSTAN 91-98/2(2001) : 2001
|
LUBRICATING OIL, GAS TURBINE ENGINE, SYNTHETIC GRADE 7.5 CST NATO CODE: O-149 JOINT SERVICE DESIGNATION: OX-38
|
BS 4A 4-1.3:1967
|
Specification for test pieces and test methods for metallic materials. Tensile tests Uninterrupted creep and rupture tests. Metric units
|
ASME B46.1 : 2009
|
SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
|
BS HR 650:1972
|
Specification for high expansion heat-resisting steel bar and wire for the manufacture of bolts, studs, set screws and nuts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (limiting ruling section 20 mm)
|
SAE AS 954 : 2011
|
WRENCHES, HAND, TWELVE POINT, HIGH STRENGTH, THIN WALL
|
BS 1134-2:1990
|
Assessment of surface texture. Guidance and general information
|
SAE AMS 5732 : 2012
|
STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING AND RINGS, 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, CONSUMABLE ELECTRODE MELTED 1800 DEGREES F (982 DEGREES C), SOLUTION AND PRECIPITATION HEAT TREATED
|
SBAC TS 48 : 4
|
TECHNICAL SPECIFICATION FOR THE PERFORMANCE OF SOCKETS AND RING SPANNERS
|
SAE AMS 2411 : 2013
|
PLATING, SILVER FOR HIGH TEMPERATURE APPLICATIONS
|
ISO 9001:2015
|
Quality management systems — Requirements
|
BS 4A 4-1.2:1967
|
Specification for test pieces and test methods for metallic materials. Tensile tests Tensile tests - elevated temperature. Metric units
|
ISO 3161:1999
|
Aerospace — UNJ threads — General requirements and limit dimensions
|
SAE AS 1310 : 2012
|
FASTENER TORQUE FOR THREADED APPLICATIONS, DEFINITIONS OF
|
ASTM E 92 : 2017 : REDLINE
|
Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
|