|
CSA C22.2 No. 94.1 : 2015
|
ENCLOSURES FOR ELECTRICAL EQUIPMENT, NON-ENVIRONMENTAL CONSIDERATIONS
|
|
ISO 4892-1:2016
|
Plastics Methods of exposure to laboratory light sources Part 1: General guidance
|
|
IEC 60364-4-43:2008
|
Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
|
|
UL 50:13ED 2015-10
|
Enclosures for Electrical Equipment, Non-Environmental Considerations
|
|
C22.1-15
|
Canadian Electrical Code, Part I (23rd Edition), Safety Standard for Electrical Installations
|
|
NFPA 780 : 2017
|
INSTALLATION OF LIGHTNING PROTECTION SYSTEMS
|
|
IEC 61587-1:2016
|
Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
|
|
IEC 60896-21:2004
|
Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
|
|
IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV
|
Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
|
|
IEC 60068-2-11:1981
|
Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
|
|
CSA C22.2 No. 144 : 1991
|
GROUND FAULT CIRCUIT INTERRUPTERS
|
|
ISO 8256:2004
|
Plastics — Determination of tensile-impact strength
|
|
UL 943:5ED 2016-05
|
Ground-Fault Circuit-Interrupters
|
|
ISO 14993:2001
|
Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions
|
|
ISO 4628-3:2016
|
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
|
|
ISO 21207:2015
|
Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying
|
|
ISO 180:2000
|
Plastics Determination of Izod impact strength
|
|
IEEE C2-2017
|
NATIONAL ELECTRICAL SAFETY CODE (NESC)(R)
|
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
|
IEC 60896-22:2004
|
Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
|
|
ISO/TS 18173:2005
|
Non-destructive testing General terms and definitions
|
|
NFPA 70 : 2017
|
NATIONAL ELECTRICAL CODE
|
|
CSA C22.2 No. 62368-1 : 2014
|
AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
|
|
IEC 61643-11:2011
|
Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
|
|
IEC 61969-3:2011
|
Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects
|
|
ISO 4892-4:2013
|
Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
|
|
IEC 61439-5:2014
|
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
|
|
ISO 4892-2:2013
|
Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
|
|
ISO 178:2010
|
Plastics Determination of flexural properties
|
|
ASTM D 471 : 2016-02
|
TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
|
|
IEC 60664-1:2007
|
Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
|
|
IEC 62485-2:2010
|
Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
|
|
CSA C22.2 No. 94.2 : 2015
|
ENCLOSURES FOR ELECTRICAL EQUIPMENT, ENVIRONMENTAL CONSIDERATIONS
|
|
ISO 3231:1993
|
Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.