Name: UNI EN 14043 : 2014
Brand: UNI

HIGH RISE AERIAL APPLIANCES FOR FIRE AND RESCUE SERVICE USE - TURNTABLE LADDERS WITH COMBINED MOVEMENTS - SAFETY AND PERFORMANCE REQUIREMENTS AND TEST METHODS

Published date

20-02-2014

Publisher

Ente Nazionale Italiano di Unificazione (UNI)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 List of significant hazards
5 Requirements
6 Designation
7 Information for use
Annex A (informative) - Example of table recording the
        stability tests
Annex B (normative) - Operating time
Annex C (informative) - List of nominal reaches in several
        European countries applicable to turntable ladders
Annex D (informative) - Verification and reception tests
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of
         EU Directive 2006/42/EC
Bibliography

This European Standard specifies the safety and performance requirements and test methods applicable to turntable ladders with combined movements of classes 18, 24, 30 and > 30 to 56, as defined in 3.13, under the control of fire-fighters and intended for fire fighting and rescuing people.

Committee	CT 34
DocumentType	Test Method
PublisherName	Ente Nazionale Italiano di Unificazione (UNI)
Status	Current
Supersedes	UNI EN 14043 : 2009

Standards	Relationship
I.S. EN 14043:2014	Identical
EN 14043:2014	Identical
BS EN 14043:2014	Identical
UNE-EN 14043:2007	Identical
DIN EN 14043:2014-04	Identical
NBN EN 14043 : 2014	Identical
NEN EN 14043 : 2014	Identical
NF EN 14043 : 2014	Identical
SN EN 14043:2014	Identical
NS EN 14043 : 2014	Identical

CISPR 12:2007+AMD1:2009 CSV	Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers
EN 1846-2:2009+A1:2013	Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance
ISO 4302:2016	Cranes Wind load assessment
EN 61000-6-3:2007/A1:2011/AC:2012	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010)
ISO/TR 11688-1:1995	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 4413:2010	Hydraulic fluid power General rules and safety requirements for systems and their components
EN 60300-1:2014	Dependability management - Part 1: Guidance for management and application
IEC 60204-1:2016	Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015	Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN ISO 7731:2008	Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN ISO 11688-2 : 2000	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 12100:2010	Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 7731:2003	Ergonomics Danger signals for public and work areas Auditory danger signals
IEC 61000-6-3:2006+AMD1:2010 CSV	Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
MIL-HDBK-217 Revision F:1991	RELIABILITY PREDICTION OF ELECTRONIC EQUIPMENT
EN 61000-6-2:2005/corrigendum:2005	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60300-1:2014	Dependability management - Part 1: Guidance for management and application
EN 1846-3:2013	Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance
IEC 60300-2:2004	Dependability management - Part 2: Guidelines for dependability management
EN ISO 12100:2010	Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN ISO 13849-1:2015	Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
CEN/TS 15989:2015	Firefighting and rescue service vehicles and equipment - Graphical symbols for control elements and displays and for markings
ISO 13850:2015	Safety of machinery Emergency stop function Principles for design
EN 1846-1:2011	Firefighting and rescue service vehicles - Part 1: Nomenclature and designation
IEC 61310-1:2007	Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 55012:2007/A1:2009	VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN ISO 4413:2010	Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
EN 1777:2010	Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and testing
EN 60300-2:2004	Dependability management - Part 2: Guidelines for dependability management
EN ISO 11688-1:2009	Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015	Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 61310-1:2008	Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 61000-6-2 : 3.0:2016	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN 60204-1 : 2006 COR 2010	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS