Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN 14382 : 2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR
Superseded date

09-08-2022

Published date

01-01-2009

Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Construction requirements
5 Functional requirements
6 Testing
7 Test and verification methods
8 Documentation
9 Marking
Annex A (informative) Ice formation
Annex B (informative) Compliance evaluation
Annex C (informative) Pressure drop and flow coefficient
Annex D (informative) Alternative test method for
        verification of the strength of the trip mechanism,
        valve seat and closing member
Annex E (informative) Sizing equation
Annex F (informative) Inspection certificate
Annex G (informative) Order specification
Annex H (informative) Acceptance test
Annex I (informative) Seat leakage (alternative requirement)
Annex J (normative) Materials
Annex K (informative) Suitability of safety shut-off device
        for damp operating conditions
Annex L (informative) Glossary
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 97/23/EC
Bibliography

Describes constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

UNI 9167 : 2009 INITIAL PRESSURE AND REDUCTION PLANTS FOR NATURAL GAS - DESIGN, CONSTRUCTION AND TESTING
UNI 10619-2 : 2014 GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 2: DESIGN, CONSTRUCTION AND TESTING - EQUIPMENT FOR GAS CONTROL
UNI 10619-1 : 2014 GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 1: DESIGN, CONSTRUCTION AND TESTING - GENERAL

EN 12732:2013+A1:2014 Gas infrastructure - Welding steel pipework - Functional requirements
EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
EN 1759-3:2003/AC:2004 FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, CLASS DESIGNATED - PART 3: COPPER ALLOY FLANGES
ISO 9606-4:1999 Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys
ISO/IEC 17050-1:2004 Conformity assessment Supplier's declaration of conformity Part 1: General requirements
ISO 9606-2:2004 Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys
EN 10226-2:2005 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN 60534-1:2005 Industrial-process control valves - Part 1: Control valve terminology and general considerations
EN ISO 15613:2004 Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys
EN 13906-1:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs
EN 1349:2009 Industrial process control valves
EN ISO 15612:2004 Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004)
ISO 15610:2003 Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables
EN 1759-1:2004 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24
IEC 60534-3-1:2000 Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves
EN 1759-4:2003 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN 1092-3:2003/AC:2007 FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
EN 12516-1:2014 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
EN ISO 9606-4:1999 Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999)
EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 15612:2004 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN ISO 15611:2003 Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003)
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
EN 13906-2:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs
EN 13445-4 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 4: FABRICATION
ISO 1431-1:2012 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
EN 12279:2000/A1:2005 GAS SUPPLY SYSTEMS - GAS PRESSURE REGULATING INSTALLATIONS ON SERVICE LINES - FUNCTIONAL REQUIREMENTS
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
EN 1092-4:2002 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 15611:2003 Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 5752:1982 Metal valves for use in flanged pipe systems Face-to-face and centre-to-face dimensions
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 148:1983 Steel — Charpy impact test (V-notch)
EN ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
IEC 60534-3-2:2001 Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves
EN 334:2005+A1:2009 Gas pressure regulators for inlet pressures up to 100 bar
EN 60534-3-2:2001 Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves
ISO 1518:1992 Paints and varnishes Scratch test
EN 10204:2004 Metallic products - Types of inspection documents
ISO 9001:2015 Quality management systems — Requirements
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
EN 60534-3-1:2000/corrigendum:2000 INDUSTRIAL-PROCESS CONTROL VALVES - PART 3-1: DIMENSIONS - FACE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, STRAIGHT PATTERN AND CENTRE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, ANGLE PATTERN CONTROL VALVES
MSS SP 55 : 2011 QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES
ISO/IEC Guide 2:2004 Standardization and related activities General vocabulary
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
EN ISO/IEC 17050-1:2010 Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements (ISO/IEC 17050-1:2004, corrected version 2007-06-15)
EN ISO 1518:2000 Paints and varnishes - Scratch test (ISO 1518:1992)
ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
EN 45020 : 2006 STANDARDIZATION AND RELATED ACTIVITIES - GENERAL VOCABULARY
EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
ISO 2409:2013 Paints and varnishes Cross-cut test
ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
EN ISO 15610:2003 Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003)
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
EN 970:1997 Non-destructive examination of fusion welds - Visual examination
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
IEC 60534-1:2005 Industrial-process control valves - Part 1: Control valve terminology and general considerations
EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
EN ISO 9606-3 : 1999 Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999)
IEC 60534-3:1976 Industrial-process control valves. Part 3: Dimensions - Section One: Face-to-face dimensions for flanged, two-way, globe-type control valves
EN ISO 175:2010 Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
ISO 9606-3:1999 Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels
EN 12186:2014 Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more