Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN 16129 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES
Superseded date

07-10-2022

Published date

04-07-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Types of regulating devices
5 Constructional characteristics
6 Performance characteristics
7 Test methods
8 Marking, packaging, instructions
Annex A (normative) - Special requirements for devices
        fitted with pressure or flow rate operated
        safety functions
Annex B (normative) - Special requirements for devices
        fitted with a thermal shut off system
Annex C (normative) - Special requirements for devices
        under extreme temperature conditions
        (temperatures below -20 degrees C)
Annex D (normative) - Regulating devices for gas cylinders
        to supply appliances installed in caravans, motor
        caravans or freshwater boats
Annex E (normative) - Complementary test requirements
        for non-metallic thermoplastic or thermal
        setting materials used in the construction of
        devices
Annex F (normative) - Requirements for electrometric
        reinforced diaphragms
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (informative) - Test method for resistance
        to corrosion
Annex J (informative) - Method for measuring leaks
Annex K (normative) - Special requirements for low
        pressure fixed regulators fitted with two or
        three outlets for outdoor use
Annex L (normative) - Special requirements for regulators
        fitted with an inlet valve
Annex M (normative) - Devices for gas cylinders to supply
        appliances installed in seawater boats
Annex N (normative) - Alternative possible seal
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2009/142/EC
         (for pressure regulators only)
Bibliography

Specifies the constructional and operational characteristics, the safety requirements, test methods and the marking of regulators and automatic change-over devices having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, for use with butane, propane and their mixtures in the vapour phase

Committee
CT 104
DevelopmentNote
Supersedes UNI EN 12864, UNI EN 13785 and UNI EN 13786. (07/2013)
DocumentType
Test Method
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
Supersedes

Standards Relationship
EN 16129:2013 Identical

UNI 7131 : 2014 LPG PLANTS FOR DOMESTIC USE NOT FED BY A DISTRIBUTION NETWORK - DESIGN, INSTALLATION AND COMMISSIONING

EN 15202:2012 LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections
EN 751-3:1996/AC:1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
CGA V 1 : 2013 STANDARD FOR COMPRESSED GAS CYLINDER VALVE OUTLET AND INLET CONNECTIONS
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
EN 10226-2:2005 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN ISO 4892-3:2016 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
ISO 75:1987 Plastics and ebonite Determination of temperature of deflection under load
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
EN 561:2002 Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
EN 560:2005/AC:2007 GAS WELDING EQUIPMENT - HOSE CONNECTIONS FOR EQUIPMENT FOR WELDING, CUTTING AND ALLIED PROCESSES
EN ISO 9227:2017 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
EN 13878 : 2003 LEISURE ACCOMMODATION VEHICLES - TERMS AND DEFINITIONS
EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
EN 1774:1997 Zinc and zinc alloys - Alloys for foundry purposes - Ingot and liquid
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
EN ISO 4628-3:2016 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016)
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
EN 521:2006 Specifications for dedicated liquefied petroleum gas appliances - Portable vapour pressure liquefied petroleum gas appliances
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 1563:2011 Founding - Spheroidal graphite cast irons
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
EN 12420:2014 Copper and copper alloys - Forgings
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
EN 12844:1998 Zinc and zinc alloys - Castings - Specifications
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 178:2010 Plastics Determination of flexural properties
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more