Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN 1854 : 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
Superseded date

08-05-2023

Published date

24-07-2010

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common use
  in the various countries
Annex B (informative) - Leak-tightness test - volumetric
  method
Annex C (informative) - Leak-tightness test - pressure loss
  method
Annex D (informative) - Conversion of pressure loss into
  leakage rate
Annex E (normative) - Electrical/electronic component
  fault modes
Annex F (normative) - Additional requirements for safety
  accessories and pressure accessories as defined in
  EU Directive 97/23/EC
Annex G (normative) - Materials for pressurized parts
Annex H (informative) - Additional materials for pressurized
  parts
Annex I (normative) - Requirements for controls used in
  DC supplied gas burners and gas burning appliances
Annex AA (informative) - Manufacturers declaration for
  EPSDs
Annex ZA (informative) - Clauses of this European Standard
  addressing requirements or provisions of EU-Directives
Bibliography
Figures
Tables

Includes the safety, construction and performance requirements for pressure sensing devices.

Committee
CT 114
DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ONORM EN 1854 : 2010 Identical
NF EN 1854 : 2010 Identical
NS EN 1854 : 2010 Identical
EN 1854:2010 Identical
NBN EN 1854 : 2010 Identical
BS EN 1854:2010 Identical
I.S. EN 1854:2010 Identical
NEN EN 1854 : 2010 Identical
SN EN 1854 : 2010 Identical
DIN EN 1854:2010-10 Identical
UNE-EN 1854:2010 Identical

IEC 61000-4-8 : 2.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-8: TESTING AND MEASUREMENT TECHNIQUES - POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST
UNI 663 : 1968 TUBI SENZA SALDATURA DI ACCIAIO NON LEGATO. TUBI LISCI PER USI GENERICI. QUALITA, PRESCRIZIONI E PROVE.
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ASTM B 85 : 2003 Standard Specification for Aluminum-Alloy Die Castings
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
ISO 274:1975 Copper tubes of circular section — Dimensions
IEC 60191-1:2007 Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices
EN 60730-2-6:2016 Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
ISO 7637-3:2016 Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
DIN 1693 : 1961
EN 10028-3:2017 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
UNI 4894 : 62 AMD 1 90 LEGHE DI RAME DA LAVORAZIONE PLASTICA. OTTONE BINARIO CON CU 67% E ZN 33%.
EN 13906-1:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs
EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
EN 12067-2:2004 Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types
EN 175301-803:2006 Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 1643:2014 Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves
ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
EN 485-2:2016 ALUMINIUM AND ALUMINIUM ALLOYS - SHEET, STRIP AND PLATE - PART 2: MECHANICAL PROPERTIES
EN 10028-6:2017 Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered
IEC 61000-4-11:2004+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
EN 60127-1:2006/A2:2015 MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS
ISO 1083:2004 Spheroidal graphite cast irons - Classification
ASTM A 395/A395M : 1999 Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures
SAE J 429 : 2014 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
ASTM A 694/A694M : 2016 : REDLINE Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 12067-1 : 98 AMD 1 2003 GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES
ISO 7637-2:2011 Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only
EN 10111:2008 Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
EN 10087:1998 Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods
ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
EN 586-2:1994 Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements
ASTM A 707/A707M : 2014 : REDLINE Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
IEC 61000-4-8:2009 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
IEC 61000-4-4:2012 RLV Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test
ASTM B 584 : 2014 : REDLINE Standard Specification for Copper Alloy Sand Castings for General Applications
IEC 60730-2-6:2015 Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
EN 61000-4-2:2009 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
UNI 9001-2 : 1987 ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. GRUPPO ALLUMINIO. AL 99,5 (1050 A).
IEC 61810-1:2015 Electromechanical elementary relays - Part 1: General and safety requirements
IEC 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 61558-2-17:1997 Safety of power transformers, power supply units and similar - Part 2-17: Particular requirements for transformers for switch mode power supplies
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links
EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
API 5L : 2012 LINE PIPE
EN 10277-3:2008 Bright steel products - Technical delivery conditions - Part 3: Free-cutting steels
EN 10028-2:2017 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
IEC 61000-4-6 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
IEC 61000-4-6:2013 Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
EN 61000-4-3 : 2006 AMD 2 2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST
ISO 3506:1979 Corrosion-resistant stainless steel fasteners — Specifications
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ASTM A 420/A420M : 2016 : REDLINE Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
IEC 61558-2-17:1997 Safety of power transformers, power supply units and similar - Part2: Particular requirements for transformers for switch mode powersupplies
EN 13906-2:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs
BS 1387:1985 Specification for screwed and socketed steel tubes and tubulars and for plain end steel tubes suitable for welding or for screwing to BS 21 pipe threads
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
EN 10272:2016 Stainless steel bars for pressure purposes
ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
EN 10028-5:2017 Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
BS 2789:1985 Specification for spheroidal graphite or nodular graphite cast iron
EN 125:2010+A1:2015 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices
IEC 61643-1:2005 Low-voltage surge protective devices - Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests
EN 1706:2010 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN 10222-5:2017 Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 10250-4:1999 Open die steel forgings for general engineering purposes - Part 4: Stainless steels
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 126:2012 Multifunctional controls for gas burning appliances
IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
UNI 5705 : 1965
EN 12516-3:2002/AC:2003 VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD
EN 10250-1:1999 Open die steel forgings for general engineering purposes - Part 1: General requirements
EN 61000-4-8:2010 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
DIN 1630:1984-10 HIGH PERFORMANCE SEAMLESS CIRCULAR UNALLOYED STEEL TUBES - TECHNICAL DELIVERY CONDITIONS
UNI 4892 : 62 AMD 1 90 LEGHE DI RAME DA LAVORAZIONE PLASTICA. OTTONE BINARIO CON CU 63% E ZN 37%.
IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
EN 13611:2015/AC:2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
EN 10250-2:1999 Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels
BS 1490:1988 Specification for aluminium and aluminium alloy ingots and castings for general engineering purposes
ASTM A 217/A217M : 2014 : REDLINE Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
EN 10213-3 : 1995 TECHNICAL DELIVERY CONDITIONS FOR STEEL CASTINGS FOR PRESSURE PURPOSES - PART 3: STEEL GRADES FOR USE AT LOW TEMPERATURES
EN 10214 : 1995 CONTINUOUSLY HOT-DIP ZINC-ALUMINIUM (ZA) COATED STEEL STRIP AND SHEET - TECHNICAL DELIVERY CONDITIONS
EN 1563:2011 Founding - Spheroidal graphite cast irons
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
UNI 3158 : 1977 AMD 152 1985 CAST UNALLOYED QUALITY STEELS FOR GENERAL ENGINEERING PURPOSES - QUALITIES, REQUIREMENTS AND TESTS
EN 10130:2006 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions
ASTM A 105/A105M : 2014-11 SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN 10083-1:2006 Steels for quenching and tempering - Part 1: General technical delivery conditions
EN 10083-2:2006 Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
EN 61058-1:2002/A2:2008 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
EN 61000-4-4:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012)
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
EN 754-2:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
UNI 7729 : 1984 TUBI SENZA SALDATURA, CON ESTREMITA LISCE, DI ACCIAIO NON LEGATO DI QUALITA, PER APPLICAZIONI MECCANICHE.
EN 61000-4-6:2014/AC:2015 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
UNI 9006-4 : 1987 ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. LEGHE ALLUMINIO-MAGNESIO-SILICIO. LEGA AL SI 1 MG 0,9 MN 0,7 (6082).
ASTM A 312/A312M : 2017-03 SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES
EN 1106:2010 Manually operated taps for gas burning appliances
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 301:2006 Zinc alloy ingots intended for castings
IEC 61000-4-29:2000 Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
EN 10028-4:2017 Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
UNI 9006-1 : 1988 ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA. LEGHE ALLUMINIO-MAGNESIO-SILICIO. LEGA AL MG 0,5 SI 0,4 FE 0,2 (6060).
UNI 9002-5 : 1989 ALLUMINIO E LEGHE DI ALLUMINIO PRIMARIE DA LAVORAZIONE PLASTICA - LEGHE ALLUMINIO-RAME - LEGA AL CU 5,5 PB 0,4 BI 0,4 (2011)
EN 1982:2017 Copper and copper alloys - Ingots and castings
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 1652:1997/AC:2003 COPPER AND COPPER ALLOYS - PLATE, SHEET, STRIP AND CIRCLES FOR GENERAL PURPOSES
EN 755-2:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
EN 61000-4-29:2000 Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
EN 60730-1:2016 Automatic electrical controls - Part 1: General requirements
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN 10222-1:2017 Steel forgings for pressure purposes - Part 1: General requirements for open die forgings
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
SAE J 995 : 2012 MECHANICAL AND MATERIAL REQUIREMENTS FOR STEEL NUTS
DIN 2391-2:1994-09 SEAMLESS PRECISION STEEL TUBES - PART 2: TECHNICAL DELIVERY CONDITIONS
IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
EN 257:2010 Mechanical thermostats for gas-burning appliances
EN 12078:1998 Zero governors for gas burners and gas burning appliances

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more