Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN ISO 14405-2 : 2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES
Superseded date

01-09-2022

Published date

01-01-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and rules for indication of dimensions and
  related tolerances
5 Units used in drawings for dimensions
6 Indication of tolerances for linear and angular
  dimensions
7 Illustrations of ambiguous +/- tolerancing vs - unambiguous
  geometrical tolerancing
8 Angular tolerancing
Annex A (informative) - Explanations and examples of the
        ambiguity caused by using +/- tolerances for
        dimensions other than linear size
Annex B (informative) - Relation to the GPS matrix model
Bibliography

Depicts the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy

Standards Relationship
EN ISO 14405-2:2011 Identical
ISO 14405-2:2011 Identical

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
ISO 3040:2016 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
ISO 81714-1:2010 Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules
ISO 2538:1998 Geometrical Product Specifications (GPS) Series of angles and slopes on prisms
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more