Emission control - Copper and copper alloy melting plants

Available format(s)

Hardcopy , PDF

Language(s)

German - English

Published date

01-04-2013

Publisher

Verlag des Vereins Deutscher Ingenieure

Preliminary Note
Introduction
1. Scope
2. Terms and definitions
3. Technology
4. Emission control measures
5. Emissions values
6. Instructions for emission measurements
7. Waste
8. Cooling water and waste water
9. Energy efficiency, heat recovery
Annex - Block diagrams of example melting plants
Bibliography
Term index English - German

The guideline describes the current state of the art of copper and copper alloy melting plants as well as the suitable emission reduction measures.

DocumentType	Standard
Pages	86
PublisherName	Verlag des Vereins Deutscher Ingenieure
Status	Current
Supersedes	VDI 2102 Blatt 2:2011-08 (Draft) VDI 2102 Blatt 2:2002-03

VDI 3883 Blatt 1:2015-09	Effects and assessment of odours - Assessment of odour annoyance - Questionnaires
TRGS 557 : 2008
VDI 2102 Blatt 1:2007-04 (Draft)	Emission control - Secondary copper smelting and refining plants
ISO/IEC 17025:2005	General requirements for the competence of testing and calibration laboratories
DIN 1701:1980-05	REFINED NICKEL
ISO 23210:2009	Stationary source emissions Determination of PM10/PM2,5 mass concentration in flue gas Measurement at low concentrations by use of impactors
VDI 3677 Blatt 3:2012-11	Filtering-separators - High-temperature gas filtration
EN 1948-2:2006	Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 2: Extraction and clean-up of PCDDs/PCDFs
VDI 3481 Blatt 1:1975-08	Gaseous emission measurement; determination of hydrocarbon concentration; flame-ionization-detector (FID)
DIN EN 573-3:2013-12	ALUMINIUM AND ALUMINIUM ALLOYS - CHEMICAL COMPOSITION AND FORM OF WROUGHT PRODUCTS - PART 3: CHEMICAL COMPOSITION AND FORM OF PRODUCTS
DIN EN 14791:2006-04	STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULPHUR OXIDES - STANDARD REFERENCE METHOD
CEN/TS 14793:2005	Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method
VDI 4085:2017-04	Planning, construction and managing of scrapyards - Facilities and equipment for the handling, storage and treatment of scraps and other materials
DIN EN 1948-4:2014-03	STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF PCDDS/PCDFS AND DIOXIN-LIKE PCBS - PART 4: SAMPLING AND ANALYSIS OF DIOXIN-LIKE PCBS
DIN EN 14790:2006-04	STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE WATER VAPOUR IN DUCTS - STANDARD REFERENCE METHOD
DIN EN 1911:2010-12	Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method
DIN EN 12659:1999-11	LEAD AND LEAD ALLOYS - LEAD
VDI 3882 Blatt 2:1994-09	Olfactometry - Determination of hedonic odour tone
DIN EN 1179:2003-09	ZINC AND ZINC ALLOYS - PRIMARY ZINC
TRD 604-1 : 2000	OPERATION OF STEAM BOILER PLANTS WITH STEAM GENERATORS OF GROUP 4 WITHOUT PERMANENT SUPERVISION
EN 1976:2012	Copper and copper alloys - Cast unwrought copper products
EN 13725:2003/AC:2006	AIR QUALITY - DETERMINATION OF ODOUR CONCENTRATION BY DYNAMIC OLFACTOMETRY
EN 15259:2007	Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
PREN 14181 : DRAFT 2012	STATIONARY SOURCE EMISSIONS - QUALITY ASSURANCE OF AUTOMATED MEASURING SYSTEMS
EN 1978:1998	Copper and copper alloys - Copper cathodes
TRD 604-2 : 1996	OPERATION OF STEAM BOILER PLANTS WITH HOT WATER GENERATORS OF GROUP 4 WITHOUT PERMANENT SUPERVISION
VDI 4220:2011-04	Quality assurance - Requirements on bodies for the determination of air pollutants at stationary sources and in ambient air
EN 12659:1999	Lead and lead alloys - Lead
VDI 2448 Blatt 2:1997-07	Statistical evaluation of random-sample measurements of stationary source emissions: Determination of the upper confidence limit
EN 13284-1:2017	Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
EN 1981:2003	Copper and copper alloys - Master alloys
VDI 1000:2017-02	VDI Standardisation Work - Principles and procedures
VDI 3677 Blatt 1:2010-11	Filtering separators - Surface filters
DIN EN ISO 23210:2009-12	Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009)
EN 15058:2017	Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry
VDI 4285 Blatt 1:2005-06	Determination of diffusive emissions by measurement - Basic concepts
EN 1948-1:2006	Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 1: Sampling of PCDDs/PCDFs
DIN EN 13284-1:2015-12 (Draft)	STATIONARY SOURCE EMISSIONS - DETERMINATION OF LOW RANGE MASS CONCENTRATION OF DUST - PART 1: MANUAL GRAVIMETRIC METHOD
DIN CEN/TS 14793:2005-06	STATIONARY SOURCE EMISSION - INTRALABORATORY VALIDATION PROCEDURE FOR AN ALTERNATIVE METHOD COMPARED TO A REFERENCE METHOD
EN 1911:2010	Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method
EN 1179:2003	Zinc an zinc alloys - Primary zinc
DIN EN 12619:2013-04	Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method
EN 576:2003	Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting - Specifications
VDI 3674:2013-04	Waste gas cleaning by adsorption - Process gas and waste gas cleaning
VDI 4285 Blatt 2:2011-03	Determination of diffusive emissions by measurements - Industrial halls and livestock farming
VDI 4219:2009-08	Determination of the uncertainty of emission measurements by use of discontinuous measurement methods
EN 1977:2013	Copper and copper alloys - Copper drawing stock (wire rod)
EN 14790:2017	Stationary source emissions - Determination of the water vapour in ducts - Standard reference method
VDI 3676:1999-10	Inertial Separators
DIN EN 14789:2006-04	STATIONARY SOURCE EMISSIONS - DETERMINATION OF VOLUME CONCENTRATION OF OXYGEN - STANDARD REFERENCE METHOD: PARAMAGNETISM
DIN EN 14181:2015-02	Stationary source emissions - Quality assurance of automated measuring systems
DIN EN 15058:2006-09	STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF CARBON MONOXIDE - STANDARD REFERENCE METHOD: NON-DISPERSIVE INFRARED SPECTROMETRY
DIN EN 12861:1999-10	COPPER AND COPPER ALLOYS - SCRAP
DIN EN 13725:2003-07	Air quality - Determination of odour concentration by dynamic olfactometry
DIN EN 1976:2013-01	COPPER AND COPPER ALLOYS - CAST UNWROUGHT COPPER PRODUCTS
VDI 3882 Blatt 1:1992-10	Olfactometry; determination of odour intensity
VDI 2066 Blatt 1:1975-10	Particulate matter measurement; measuring of particulate matter in flowing gases; gravimetric determination of dust load; fundamentals
DIN EN 14792:2006-04	STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF NITROGEN OXIDES - STANDARD REFERENCE METHOD: CHEMILUMINESCENCE
EN 14792:2017	Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence
PREN 1977 : DRAFT 2011	COPPER AND COPPER ALLOYS - COPPER DRAWING STOCK (WIRE ROD)
EN 1948-4:2010+A1:2013	STATIONARY SOURCE EMISSIONS - DETERMINATION OF THE MASS CONCENTRATION OF PCDDS/PCDFS AND DIOXIN-LIKE PCBS - PART 4: SAMPLING AND ANALYSIS OF DIOXIN-LIKE PCBS
VDI 2450 Blatt 1:1977-09	Measurement of air pollutant emission, transmission, and immission; definitions and glossary of terms
EN 573-3:2013	Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
DIN EN 15259:2008-01	Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
VDI 3950:2006-12	Stationary source emissions - Quality assurance of automated measuring and electronic data evaluation systems