• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN ISO 10407-2:2008

Current
Current

The latest, up-to-date edition.

PETROLEUM AND NATURAL GAS INDUSTRIES - ROTARY DRILLING EQUIPMENT - PART 2: INSPECTION AND CLASSIFICATION OF USED DRILL STEM ELEMENTS
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2008

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
   4.1 Symbols
   4.2 Abbreviated terms
5 Conformance
   5.1 Basis for inspection
   5.2 Repeatability of results
   5.3 Ordering inform
6 Quality assurance
   6.1 General
   6.2 Standardization and operating procedures
   6.3 Equipment des
   6.4 Personnel qualification
   6.5 Dynamic test data demonstrating the system capabilities
         for detecting the reference indicators
   6.6 Reports
7 Qualification of inspection personnel
   7.1 General
   7.2 Written procedure
   7.3 Qualification responsibility and requirements
   7.4 Training programmes
   7.5 Examinations
   7.6 Experience
   7.7 Re-qualification
   7.8 Documentation
   7.9 NDT personnel certification
8 General inspection procedures
   8.1 General
   8.2 Owner/operator work site requirements for quality
         inspection
   8.3 Documents at job site
   8.4 Pre-inspection procedures
   8.5 Drill-pipe and tool-joint classification markings
   8.6 Post-inspection procedures
9 General non-destructive inspection method requirements
   9.1 General
   9.2 Equipment
   9.3 Illumination
   9.4 Magnetic-particle-inspection equipment
   9.5 Ultrasonic
   9.6 Electromagnetic inspection units
10 Drill stem element inspection and classification
   10.1 Pipe body - Full-length visual inspection
   10.2 Drill body - Outside diameter gauging
   10.3 Pipe body - Ultrasonic wall-thickness gauging
   10.4 Pipe body - Full-length electromagnetic inspection
         (EMI)
   10.5 Pipe body - Full-length ultrasonic transverse and wall
         thickness
   10.6 Pipe body - Full-length ultrasonic transverse, wall
         thickness and longitudinal inspection
   10.7 Drill-pipe body - External magnetic-particle inspection
         of the critical area
   10.8 Drill-pipe body - Bi-directional external magnetic-particle
         inspection of the critical area
   10.9 Pipe body - Full-length wall-loss inspection
   10.10 Pipe body - Ultrasonic inspection of the critical area
   10.11 Pipe body - Calculation of cross-sectional area
   10.12 Pipe body - Document review (traceability)
   10.13 Pipe body - Evaluation and classification
   10.14 Tool joints
   10.15 Tool joints - Check for box swell and pin stretch
   10.16 Repair of rejected tool joints
   10.17 Tool joints - Check tool-joint pin and box outside
         diameter and eccentric wear
   10.18 Tool joints - Measure tool-joint pin and box outside
         diameter and check for eccentric wear
   10.19 Tool joints - Check tool-joint pin and box tong space
   10.20 Tool joints - Measure tool-joint pin and box tong
         space
   10.21 Tool joint - Magnetic-particle inspection of the pin
         threads
   10.22 Tool joint - Magnetic-particle inspection of box
         threads
   10.23 Tool joints - Measure tool-joint pin inside diameter
   10.24 Magnetic-particle inspection of the connection OD for
         heat-check cracking
   10.25 Bi-directional wet magnetic-particle inspection of the
         connection OD for heat-check cracking
   10.26 Tool joints - Measure the tool-joint counterbore
         depth, pin-base length and seal width
   10.27 BHA connection - Visual inspection of bevels, seals,
         threads and stress-relief features
   10.28 BHA - Measure box outside diameter, pin inside
         diameter, counterbore diameter and benchmark l
         ocation if a benchmark is present
   10.29 BHA - Check bevel diameter
   10.30 BHA - Measure bevel diameter
   10.31 BHA - Magnetic-particle inspection of the pin and box
         threads
   10.32 BHA connection - Liquid-penetrant inspection of the
         pin and box threads
   10.33 BHA - Dimensional measurement of stress-relief
         features
   10.34 Length measurements of the counterbore, pin and pin
         neck
   10.35 Drill collar - Visual full-length OD and ID, markings,
         fish-neck length and tong space
   10.36 Drill-collar elevator groove and slip-recess
         magnetic-particle inspection
   10.37 Drill-collar elevator-groove and slip-recess
         measurement
   10.38 Subs (full-length visual OD and ID), fish-neck length,
         section-change radius and markings
   10.39 Float-bore recess measurements
   10.40 Magnetic-particle inspection of subs - Full-length,
         internal and external
   10.41 HWDP - Visual full-length OD and ID, markings and
         tong space
   10.42 Visual inspection and wear pattern report for kelly
   10.43 Magnetic-particle evaluation of critical areas on kellys
   10.44 Magnetic-particle evaluation, full length, of the drive
         section on kellys
   10.45 Stabilizer (full-length visual OD and ID), fish-neck
         length, blade condition, ring gauge and markings
   10.46 Magnetic-particle inspection of the base of stabilizer
         blades for cracking
   10.47 Function test
   10.48 Bi-directional, wet magnetic-particle inspection of the
         base of stabilizer blade for cracking
   10.49 Visual inspection of jars (drilling and fishing),
         accelerators and shock subs
   10.50 Maintenance review
   10.51 Dimensional measurement of wear areas as specified
         by OEM requirements
   10.52 Original equipment manufacturer designated testing
         for used equipment
   10.53 MWD/LWD - Visual, full-length OD and ID, and
         markings, including visual inspection of
         hard-banding and coatings
   10.54 Motors and turbines - Visual, full-length OD and ID
         and markings, including visual inspection of
         hard-banding and coatings
   10.55 Reamers, scrapers, and hole openers - Visual,
         full-length OD and ID and markings, including
         visual inspection of hard-banding and coatings
   10.56 Rotary steerable - Visual, full-length OD and ID
         and markings, including visual inspection of
         hard-banding
   10.57 Full-length drift
   10.58 Proprietary equipment inspection
   10.59 Hard-banding inspection
   10.60 Transverse magnetic-particle inspection of tool-joint
         OD and ID under the pin threads
   10.61 Drill-pipe body - Internal magnetic-particle inspection
         of the critical area
   10.62 Drill-pipe body - Bi-directional, internal
         magnetic-particle inspection of the critical
         area
   10.63 API external upset-thread connection inspection
Annex A (normative) Original equipment manufacturer
        (OEM) requirements
Annex B (normative) Required and additional inspections
        by product and class of service
Annex C (normative) SI units
Annex D (informative) USC units
Annex E (informative) Inspection-level guidelines
Annex F (informative) Proprietary drill stem connection
        inspection
Annex G (informative) Used work-string tubing proprietary-connection
        thread inspection
Bibliography

Describes the required inspection for each level of inspection and procedures for the inspection and testing of used drill stem elements.

DocumentType
Standard
Pages
234
PublisherName
National Standards Authority of Ireland
Status
Current

Standards Relationship
EN ISO 10407-2:2008/AC:2009 Identical

ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
API 7-2 : 2017 THREADING AND GAUGING OF ROTARY SHOULDERED CONNECTIONS
API 7A1 : 1992 RECOMMENDED PRACTICE FOR TESTING OF THREAD COMPOUND FOR ROTARY SHOULDERED CONNECTIONS
API 7-1 : 2006 : ADD 3:2011(R2015) SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS
API Q1 : 2013 SPECIFICATION FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS FOR MANUFACTURING ORGANIZATIONS FOR THE PETROLEUM AND NATURAL GAS INDUSTRY
API 7 : 2001 SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS
ISO 11484:2009 Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
ISO 10424-2:2007 Petroleum and natural gas industries — Rotary drilling equipment — Part 2: Threading and gauging of rotary shouldered thread connections
ISO 10424-1:2004 Petroleum and natural gas industries Rotary drilling equipment Part 1: Rotary drill stem elements
ASTM E 1220 : 2016 : REDLINE Standard Practice for Visible Penetrant Testing Using Solvent-Removable Process

View more information
£237.94
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.