|
IEC 60794-3:2014
|
Optical fibre cables - Part 3: Outdoor cables - Sectional specification
|
|
IEC 60512-11-4:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
|
|
IEC 60512-8:1993
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations
|
|
IEC 60512-11-9:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
|
|
IEC 60512-11-10:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
|
|
IEC 60512-4-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 4-2: Voltage stress tests - Test 4b: Partial discharge
|
|
IEC 60793-1-44:2011
|
Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength
|
|
IEC 60793-1-41:2010
|
Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth
|
|
IEC 60512-6-3:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
|
|
IEC 60793-2-30:2015
|
Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
|
|
IEC 60794-1-2:2017
|
Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance
|
|
ISO/IEC 11801:2002
|
Information technology Generic cabling for customer premises
|
|
IEC 60793-2-40:2015
|
Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres
|
|
IEC 61156-5-1:2009
|
Multicore and symmetrical pair/quad cables for digital communications - Part 5-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Horizontal floor wiring - Blank detail specification
|
|
ISO/IEC TR 14763-2:2000
|
Information technology Implementation and operation of customer premises cabling Part 2: Planning and installation of copper cabling
|
|
IEC 61156-6-1:2009
|
Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Blank detail specification
|
|
IEC 61918:2013
|
Industrial communication networks - Installation of communication networks in industrial premises
|
|
IEC 60512-6-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump
|
|
ISO/IEC 18010:2002
|
Information technology Pathways and spaces for customer premises cabling
|
|
IEC 60793-1-40:2001
|
Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
|
|
ISO/IEC 14763-1:1999
|
Information technology Implementation and operation of customer premises cabling Part 1: Administration
|
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
|
IEC 61076-3-106:2006
|
Connectors for electronic equipment - Product requirements - Part 3-106: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface
|
|
IEC 60512-11-7:2003
|
Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
|
|
IEC 61935-1:2015
|
Specification for the testing of balanced and coaxial information technology cabling - Part 1: Installed balanced cabling as specified in ISO/IEC 11801 and related standards
|
|
ISO/IEC TR 14763-3:2000
|
Information technology Implementation and operation of customer premises cabling Part 3: Acceptance testing for optical cabling
|
|
IEC 60512-19-3:1997
|
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance
|
|
IEC 60793-2-50:2015
|
Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
|
|
IEC 60512-11-12:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
|
|
IEC 60512-4-1:2003
|
Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
|
|
IEC 60512-9:1992
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 9: Miscellaneous tests
|
|
IEC 60794-2:2017
|
Optical fibre cables - Part 2: Indoor cables - Sectional specification
|
|
IEC 61076-2-101:2012
|
Connectors for electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking
|
|
IEC 61935-2:2010
|
Specification for the testing of balanced and coaxial information technology cabling - Part 2: Cords as specified in ISO/IEC 11801 and related standards
|
|
IEC 60512-23-3:2000
|
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories
|
|
IEC 61754-20:2012
|
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family
|
|
IEC 60512-6-4:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
|
|
IEC 61753-053-3:2004
|
Fibre optic interconnecting devices and passive components performance standard - Part 053-3: Continuously variable attenuators for category U - Uncontrolled environment
|
