We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • 09/30199358 DC : 0

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    BS EN 12697-46 - BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 46: LOW TEMPERATURE CRACKING AND PROPERTIES BY UNIAXIAL TENSION TESTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-05-2012

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Apparatus
       5.1 Testing device for conducting UTST,
            TSRST, RT and TCT
            5.1.1 Load device
            5.1.2 Deformation measurement system
            5.1.3 Load measurement system
            5.1.4 Recording equipment
            5.1.5 Thermostatic chamber
       5.2 Testing device for conducting UCTST
            5.2.1 Dynamic testing device
            5.2.2 Monitoring system
            5.2.3 Electronic signal amplifier
            5.2.4 Thermostatic chamber
            5.2.5 Recording equipment
    6 Calibration
       6.1 Testing device for conducting UTST, TSRST,
            relaxation test and tensile creep test
       6.2 Testing device for conducting UCTST
    7 Specimen preparation
       7.1 Number of samples
       7.2 Dimensions
       7.3 Sawing
       7.4 Bulk density
       7.5 Drying
       7.6 Storage
       7.7 Mounting
       7.8 Installation and Preparation
    8 Procedure
       8.1 Uniaxial tension stress test (UTST)
       8.2 Thermal stress restrained specimen
            test (TSRST)
       8.3 Relaxation test (RT)
       8.4 Tensile creep test (TCT)
       8.5 Uniaxial cyclic tensile stress test (UCTST)
            8.5.1 Test temperature and test frequency
            8.5.2 Base stress
            8.5.3 Peak stress
    9 Calculation
       9.1 Tension strength reserve
       9.2 Uniaxial cyclic tensile stress test (UCTST)
    10 Test report
       10.1 General
       10.2 Information on specimen
       10.3 Information on test method
       10.4 Information on the test and results
            10.4.1 Uniaxial tension stress test (UTST)
            10.4.2 Thermal stress restrained specimen
                   test (TSRST)
            10.4.3 Tension strength reserve
            10.4.4 Relaxation test
            10.4.5 Tensile Creep Test
            10.4.6 Uniaxial cyclic tensile stress test (UCTST)
    11 Precision

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee B/510/1
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective