• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

11/30235009 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES
Available format(s)

Hardcopy , PDF

Superseded date

31-10-2013

Language(s)

English

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or
  protective measures
7 Information for use
Annex A (informative) - Selection of a suitable set
        of crane standards for a given application
Annex B (normative) - Determination of factors
Annex C (normative) - Environmental influences
Annex D (normative) - Failure mode analysis
Annex E (normative) - Material selection
Annex F (normative) - Control station instrumentation
Annex G (normative) - Wire rope safety factors
Annex H (normative) - Slewing bearings
Annex I (normative) - Requirements for brakes
Annex J (normative) - Ranking of safety systems
Annex K (normative) - Required performance levels (PLr) for
        SRP/CS according to EN ISO 13849-1:2008
Annex L (informative) - Typical general-purpose offshore
        cranes and terminology
Annex M (normative) - Design excursion envelopes
Annex N (normative) - Noise test code
Annex O (normative) - Equipment for use in a hazardous area
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC

BS EN 13852-1

Committee
MHE/3/10
DocumentType
Draft
Pages
92
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
PREN 13852-1 : DRAFT 2011 Identical

EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
EN 12385-2:2002+A1:2008 Steel wire ropes - Safety - Part 2: Definitions, designation and classification
EN 12385-4:2002+A1:2008 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
CEN/TS 13001-3-1:2004/AC:2006 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 13557:2003+A2:2008 Cranes - Controls and control stations
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 12385-1:2002+A1:2008 Steel wire ropes - Safety - Part 1: General requirements
EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
ISO 12480-1:1997 Cranes Safe use Part 1: General
EN 12644-2:2000+A1:2008 Cranes - Information for use and testing - Part 2: Marking
EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 9374-4:1989 Cranes Information to be provided Part 4: Jib cranes
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
EN 14502-1:2010 Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets
EN 12385-3:2004+A1:2008 Steel wire ropes - Safety - Part 3: Information for use and maintenance
EN 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
EN ISO 14121-1:2007 Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007)
EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
EN 13135-2:2004+A1:2010 Cranes - Equipment - Part 2: Non-electrotechnical equipment
ISO 12478-1:1997 Cranes Maintenance manual Part 1: General
EN 61310-3:2008 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
ISO 8566-1:2010 Cranes Cabins and control stations Part 1: General
ISO 9927-1:2013 Cranes — Inspections — Part 1: General
EN 13586:2004+A1:2008 Cranes - Access
EN ISO 7731:2008 Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN 50017:1998 Electrical apparatus for potentially explosive atmospheres - Powder filling "q"
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN 13411-3:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 12644-1:2001+A1:2008 Cranes - Information for use and testing - Part 1: Instructions
ISO 9374-1:1989 Cranes Information to be provided Part 1: General
EN 13411-7:2006+A1:2008 Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN 60079-11:2012 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
EN 13135-1:2003+A1:2010 Cranes - Equipment - Part 1: Electrotechnical equipment
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN 60079-25:2010/AC:2013 EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 842:1996+A1:2008 Safety of machinery - Visual danger signals - General requirements, design and testing
EN 61000-6-4:2007/A1:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
EN 13411-4:2011 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
EN 13411-6:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
EN 10204:2004 Metallic products - Types of inspection documents
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
CEN/TS 13001-3-5:2010 Cranes - General design - Part 3-5: Limit states and proof of competence of forged hooks
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
EN 10083-2:2006 Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 10025-6:2004+A1:2009 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 50015:1998 Electrical apparatus for potentially explosive atmospheres - Oil immersion "o"
EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
ISO 12482-1:1995 Cranes Condition monitoring Part 1: General
ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
CEN/TS 13001-3-2:2008 Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)

View more information
£20.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.