|
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
|
ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
|
|
ISO 1133-1:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
|
|
ISO 6964:1986
|
Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
|
|
ISO 13477:2008
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
|
|
ISO 3:1973
|
Preferred numbers Series of preferred numbers
|
|
ISO 18553:2002
|
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
|
|
ISO/TS 10839:2000
|
Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
|
|
ISO 13479:2009
|
Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
|
|
ISO 11414:2009
|
Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
|
|
ISO 12162:2009
|
Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
|
|
ISO 6259-1:2015
|
Thermoplastics pipes Determination of tensile properties Part 1: General test method
|
|
ISO 13478:2007
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
|
|
ISO 16871:2003
|
Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering
|
|
ISO 472:2013
|
Plastics Vocabulary
|
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
|
ISO 1183-1:2012
|
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
|
|
ISO 1183-2:2004
|
Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
|
|
ISO 15512:2016
|
Plastics Determination of water content
|
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
|
|
ISO 4065:1996
|
Thermoplastics pipes Universal wall thickness table
|
|
ISO 497:1973
|
Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
|
|
CEN/TS 1555-7:2013
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
|
|
ISO 6259-3:2015
|
Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
|
|
ISO 760:1978
|
Determination of water Karl Fischer method (General method)
|
|
ISO 11413:2008
|
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
|
|
ISO 1043-1:2011
|
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
|
|
EN 12099:1997
|
Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
|
|
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.