14/30290166 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
31-03-2016
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Essential principles of safety and performance
of medical devices
5 Use of standards and guides in support of the
essential principles
6 Essential principles and references to relevant
standards and guides
Annex A (informative) - Rationale and guidance
Annex B (normative) - Table relating essential principles
to standards
Annex C (informative) - Website listings of other standards
suitable for the medical device sector and for
assessment purposes
Annex D (informative) - Reference to the Essential Principles
by International Standards
Bibliography
BS ISO 16142-1
Committee |
CH/210
|
DocumentType |
Draft
|
Pages |
50
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
ISO/TS 13004:2013 | Sterilization of health care products — Radiation — Substantiation of selected sterilization dose: Method VDmaxSD |
IEC 80001-1:2010 | Application of risk management for IT-networks incorporating medical devices - Part 1: Roles, responsibilities and activities |
IEC TR 80002-1:2009 | Medical device software - Part 1: Guidance on the application of ISO 14971 to medical device software |
IEC 60336:2005 | Medical electrical equipment - X-ray tube assemblies for medical diagnosis - Characteristics of focal spots |
ISO/TR 24971:2013 | Medical devices Guidance on the application of ISO 14971 |
ISO 14160:2011 | Sterilization of health care products Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives Requirements for characterization, development, validation and routine control of a sterilization process for medical devices |
ISO 15882:2008 | Sterilization of health care products — Chemical indicators — Guidance for selection, use and interpretation of results |
IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
IEC PAS 61910-1:2007 | Medical electrical equipment - Radiation dose documentation - Part 1: Equipment for radiography and radioscopy |
ASTM F 2212 : 2011 : REDLINE | Standard Guide for Characterization of Type I Collagen as Starting Material for Surgical Implants and Substrates for Tissue Engineered Medical Products (TEMPs) |
IEC 60522:1999 | Determination of the permanent filtration of X-ray tube assemblies |
IEC 60601-1-6:2010+AMD1:2013 CSV | Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: Usability |
ISO 13485:2016 | Medical devices Quality management systems Requirements for regulatory purposes |
ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
ISO 25424:2009 | Sterilization of medical devices Low temperature steam and formaldehyde Requirements for development, validation and routine control of a sterilization process for medical devices |
ISO 7405:2008 | Dentistry Evaluation of biocompatibility of medical devices used in dentistry |
IEC 60601-1-8:2006+AMD1:2012 CSV | Medical electrical equipment - Part 1-8: General requirements forbasic safety and essential performance - Collateral Standard: General requirements, tests and guidance for alarm systems inmedical electrical equipment and medical electrical systems |
ISO/TS 19218-1:2011 | Medical devices Hierarchical coding structure for adverse events Part 1: Event-type codes |
ISO 21969:2009 | High-pressure flexible connections for use with medical gas systems |
ISO/IEC Guide 63:2012 | Guide to the development and inclusion of safety aspects in International Standards for medical devices |
ASTM F 2027 : 2016 : REDLINE | Standard Guide for Characterization and Testing of Raw or Starting Materials for Tissue-Engineered Medical Products |
IEC 62366:2007+AMD1:2014 CSV | Medical devices - Application of usability engineering to medical devices |
ISO 14630:2012 | Non-active surgical implants General requirements |
ISO 9584:1993 | Implants for surgery — Non-destructive testing — Radiographic examination of cast metallic surgical implants |
ISO 690-2:1997 | Information and documentation Bibliographic references Part 2: Electronic documents or parts thereof |
IEC 60601-1-2:2014 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
ISO 5359:2014 | Anaesthetic and respiratory equipment Low-pressure hose assemblies for use with medical gases |
EN 1041:2008+A1:2013 | Information supplied by the manufacturer of medical devices |
ISO/IEC Guide 51:2014 | Safety aspects Guidelines for their inclusion in standards |
IEC 62304:2006+AMD1:2015 CSV | Medical device software - Software life cycle processes |
ISO 18472:2006 | Sterilization of health care products Biological and chemical indicators Test equipment |
ISO 16061:2015 | Instrumentation for use in association with non-active surgical implants General requirements |
IEC TR 60878:2015 | Graphical symbols for electrical equipment in medical practice |
ISO 9583:1993 | Implants for surgery — Non-destructive testing — Liquid penetrant inspection of metallic surgical implants |
IEC 60580:2000 | Medical electrical equipment - Dose area product meters |
ISO 20857:2010 | Sterilization of health care products Dry heat Requirements for the development, validation and routine control of a sterilization process for medical devices |
ISO 15985:2014 | Plastics — Determination of the ultimate anaerobic biodegradation under high-solids anaerobic-digestion conditions — Method by analysis of released biogas |
ISO 10993-11:2017 | Biological evaluation of medical devices — Part 11: Tests for systemic toxicity |
ASTM F 2761 : 2009 : R2013 | Medical Devices and Medical Systems - Essential safety requirements for equipment comprising the patient-centric integrated clinical environment (ICE) - Part 1: General requirements and conceptual model |
IEC 60601-1-3:2008+AMD1:2013 CSV | Medical electrical equipment - Part 1-3: General requirements forbasic safety and essential performance - Collateral Standard: Radiation protection in diagnostic X-ray equipment |
ISO 10993-1:2009 | Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process |
ISO 6474:1994 | Implants for surgery Ceramic materials based on high purity alumina |
IEC 62471:2006 | Photobiological safety of lamps and lamp systems |
ISO 7153-1:2016 | Surgical instruments Materials Part 1: Metals |
IEC 60627:2013 | Diagnostic X-ray imaging equipment - Characteristics of general purpose and mammographic anti-scatter grids |
ISO 14969:1999 | Quality systems Medical devices Guidance on the application of ISO 13485 and ISO 13488 |
ISO 14155:2011 | Clinical investigation of medical devices for human subjects Good clinical practice |
IEC 61217:2011 | Radiotherapy equipment - Coordinates, movements and scales |
ISO 8828:2014 | Implants for surgery Guidance on care and handling of orthopaedic implants |
ISO 13402:1995 | Surgical and dental hand instruments — Determination of resistance against autoclaving, corrosion and thermal exposure |
ISO 14971:2007 | Medical devices Application of risk management to medical devices |
ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
AAMI TIR49 : 2013 | DESIGN OF TRAINING AND INSTRUCTIONAL MATERIALS FOR MEDICAL DEVICES USED IN NON-CLINICAL ENVIRONMENTS |
ISO 13782:1996 | Implants for surgery Metallic materials Unalloyed tantalum for surgical implant applications |
ISO 14161:2009 | Sterilization of health care products Biological indicators Guidance for the selection, use and interpretation of results |
ISO 15223-1:2016 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements |
IEC 60601-1-9:2007+AMD1:2013 CSV | Medical electrical equipment - Part 1-9: General requirements forbasic safety and essential performance - Collateral Standard: Requirements for environmentally conscious design |
ISO 17664:2017 | Processing of health care products Information to be provided by the medical device manufacturer for the processing of medical devices |
ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.