• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

14/30298206 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS EN 1570-2 - SAFETY REQUIREMENTS FOR LIFTING TABLES - PART 2: LIFTING TABLES SERVING MORE THAN 2 FIXED LANDINGS OF A BUILDING, FOR LIFTING GOODS WITH A VERTICAL TRAVEL SPEED NOT EXCEEDING 0,15 M/S
Available format(s)

Hardcopy , PDF

Superseded date

31-12-2016

Language(s)

English

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or measures
7 Information for the user
Annex A (informative) - Overloading
Annex B (normative) - Noise
Annex C (normative) - Practical test procedures
Annex D (informative) - Signs
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of
         EU Directive 2006/42/CE

BS EN 1570-2.

Committee
MHE/4
DocumentType
Draft
Pages
39
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
PREN 1570-2 : DRAFT 2014 Identical

ISO 2408:2017 Steel wire ropes — Requirements
ISO 4308-1:2003 Cranes and lifting appliances Selection of wire ropes Part 1: General
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
CLC/TS 61496-2:2006 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN ISO 14121-1:2007 Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007)
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
IEC 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
ISO 4308-2:1988 Cranes and lifting appliances Selection of wire ropes Part 2: Mobile cranes Coefficient of utilization
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
ISO 4347:2015 Leaf chains, clevises and sheaves Dimensions, measuring forces, tensile strengths and dynamic strengths
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 4301-1:2016 Cranes — Classification — Part 1: General
EN ISO 4413:2010 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
EN 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
£20.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.