15/30324901 DC : 0
NA
Status of Standard is Unknown
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for constituent
materials
5 Performance characteristics
for intended uses
6 Product Characteristics
7 Sampling
8 Assessment and verification of
the constancy of performance - AVCP
9 Marking and labelling
Annex A (informative) - Minimum frequency
of testing for FPC
Annex B (informative) - Test methods for
special applications
Annex C (informative) - Electrical resistivity
Annex ZA (informative) - Clauses of this
European Standard addressing the
provisions of the EU Construction
Products Regulation
Bibliography
BS EN 1504-3.
Committee |
B/517/8
|
DocumentType |
Draft
|
Pages |
36
|
PublisherName |
British Standards Institution
|
Status |
NA
|
Standards | Relationship |
PREN 1504-3 : DRAFT 2015 | Identical |
EN 934-1:2008 | Admixtures for concrete, mortar and grout - Part 1: Common requirements |
EN 13396:2004 | Products and systems for the protection and repair of concrete structures - Test methods - Measurement of chloride ion ingress |
EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
EN ISO 11358-1:2014 | Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014) |
EN 1504-10:2017 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works |
EN 197-1:2011 | Cement - Part 1: Composition, specifications and conformity criteria for common cements |
EN 13529:2003 | Products and systems for the protection and repair of concrete structures - Test methods - Resistance to severe chemical attack |
EN 1015-17:2000/A1:2004 | METHODS OF TEST FOR MORTAR FOR MASONRY - PART 17: DETERMINATION OF CHLORIDE CONTENT OF FRESH MORTARS |
EN 12190:1998 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of compressive strength of repair mortar |
ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
EN 13687-2:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock) |
EN 480-14:2006 | Admixtures for concrete, mortar and grout - Test methods - Part 14: Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test |
EN 1542:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off |
EN 1767:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Infrared analysis |
EN 13057:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance of capillary absorption |
EN 13395-2:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 2: Test for flow of grout or mortar |
EN 13036-4:2011 | Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test |
ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
EN 13295:2004 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation |
EN 1015-11 : 1999 AMD 1 2006 | METHODS OF TEST FOR MORTAR FOR MASONRY - PART 11: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH OF HARDENED MORTAR |
EN 13501-2:2016 | Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services |
EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
EN ISO 9514:2005 | Paints and varnishes - Determination of the pot life of multicomponent coating systems - Preparation and conditioning of samples and guidelines for testing (ISO 9514:2005) |
ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
EN 14647:2005/AC:2006 | CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA |
EN 13823:2010+A1:2014 | REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM |
EN 14306:2015 | Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
EN 1877-2:2000 | Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 2: Determination of amine functions using the total basicity number |
EN 13412:2006 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression |
EN ISO 9239-1:2010 | Reaction to fire tests for floorings - Part 1: Determination of the burning behaviour using a radiant heat source (ISO 9239-1:2010) |
EN 12620:2002+A1:2008 | Aggregates for concrete |
ISO 390:1993 | Products in fibre-reinforced cement Sampling and inspection |
EN 12192-1:2002 | Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 1: Test method for dry components of premixed mortar |
EN 1504-2:2004 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete |
ISO 11358:1997 | Plastics Thermogravimetry (TG) of polymers General principles |
EN ISO 12696:2016 | Cathodic protection of steel in concrete (ISO 12696:2016) |
CEN/TS 12390-9:2016 | Testing hardened concrete - Part 9: Freeze-thaw resistance with de-icing salts - Scaling |
ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
EN 12617-4:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Part 4: Determination of shrinkage and expansion |
EN 13395-3:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 3: Test for flow of repair concrete |
ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
EN 1877-1:2000 | Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 1: Determination of epoxy equivalent |
EN 1504-1:2005 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions |
EN 1504-8:2016 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP) |
ISO 9239-1:2010 | Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source |
EN 13055-1:2002/AC:2004 | LIGHTWEIGHT AGGREGATES - PART 1: LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR AND GROUT |
EN 13687-1:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 1: Freeze-thaw cycling with de-icing salt immersion |
EN 13584:2003 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products |
EN 1766:2017 | Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing |
ISO 9514:2005 | Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing |
EN 13395-4:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 4: Application of repair mortar overhead |
EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
EN 1770:1998 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of the coefficient of thermal expansion |
ISO 12696:2016 | Cathodic protection of steel in concrete |
EN 13687-4:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 4: Dry thermal cycling |
EN 14487-1:2005 | Sprayed concrete - Part 1: Definitions, specifications and conformity |
EN ISO 11925-2:2010/AC:2011 | REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST |
EN 1504-9:2008 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 9: General principles for the use of products and systems |
EN 13395-1:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 1: Test for flow of thixotropic mortars |
EN 13294:2002 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.