• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

17/30244737 DC : 0

NA
NA

Status of Standard is Unknown

BS EN 17149 - RAILWAY APPLICATIONS - FATIGUE STRENGTH ASSESSMENT OF RAILWAY VEHICLE STRUCTURES BASED ON CUMULATIVE DAMAGE
Available format(s)

Hardcopy , PDF

Language(s)

English

European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Stress determination
5 Fatigue resistance
6 Concept of partial factors
7 Procedure of fatigue assessment
Annex A (informative) - Procedure for determination
        of mean stress factors for non-welded
        and welded structures
Annex B (informative) - Example specification for
        permissible of volumetric defects in
        castings of steel, iron and aluminium
Annex C (normative) - Surface roughness factor
        for cut edges of steel
Annex D (normative) - Reference values of the fatigue
        strength [Delta][sigma][c] and [Delta][tau][c] for
        notch cases of welded structures of steel
Annex E (normative) - Reference values of the fatigue
        strength [Delta][sigma][c] and [Delta][tau][c] for
        notch cases of welded structures of aluminium
Annex F (normative) - Thickness influence for welded
        structures of steel and consideration of bending
        for welded structures of steel and of aluminium
Annex G (informative) - Enhancement of reference
        value of the fatigue strength [Delta][sigma][c] for
        load carrying T- and cruciform joints with double
        fillet weld with or without partial penetration
Annex H (informative) - Application of structural
        stress assessment for welded structures of steel
        and aluminium
Annex I (informative) - Application of notch stress
        assessment for welded structures of steel and
        aluminium
Annex J (informative) - Example for fatigue assessment
Annex K (informative) - Determination of nominal
        stresses in weld root of single sided partial
        penetration welds
Bibliography

BS EN 17149.

Committee
RAE/3/-/11
DocumentType
Draft
Pages
134
PublisherName
British Standards Institution
Status
NA

Standards Relationship
PREN 17149 : DRAFT 2017 Identical

ASTM E 446 : 2015 : REDLINE Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
EN 12680-2:2003 Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components
ASTM E 186 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings
EN 10213:2007+A1:2016 Steel castings for pressure purposes
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
EN 15085-1:2007+A1:2013 Railway applications - Welding of railway vehicles and components - Part 1: General
EN 12680-1:2003 Founding - Ultrasonic examination - Part 1: Steel castings for general purposes
EN 485-2:2016 ALUMINIUM AND ALUMINIUM ALLOYS - SHEET, STRIP AND PLATE - PART 2: MECHANICAL PROPERTIES
DVS 0905:2017-02 INDUSTRIELLE ANWENDUNG DES KERBSPANNUNGSKONZEPTES FUER DEN ERMUEDUNGSFESTIGKEITSNACHWEIS VON SCHWEISSVERBINDUNGEN
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
ISO 2394:2015 General principles on reliability for structures
EN 586-2:1994 Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements
ASTM E 155 : 2015 : REDLINE Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
EN 15085-5:2007 Railway applications - Welding of railway vehicles and components - Part 5: Inspection, testing and documentation
EN 1370:2011 Founding - Examination of surface condition
EN 1706:2010 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN 1371-1:2011 Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings
EN 12680-3:2011 Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings
EN 1563:2011 Founding - Spheroidal graphite cast irons
EN 1369:2012 Founding - Magnetic particle testing
ASTM E 280 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
EN 12681 : 2003 FOUNDING - RADIOGRAPHIC EXAMINATION
EN 1993-1-9:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE
EN 12663-1:2010+A1:2014 Railway applications - Structural requirements of railway vehicle bodies - Part 1: Locomotives and passenger rolling stock (and alternative method for freight wagons)
EN 15085-2:2007 Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer
EN 12663-2:2010 Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons
EN 13749:2011 Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames
EN 15085-3:2007/AC:2009 RAILWAY APPLICATIONS - WELDING OF RAILWAY VEHICLES AND COMPONENTS - PART 3: DESIGN REQUIREMENTS
EN 1999-1-3:2007/A1:2011 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-3: STRUCTURES SUSCEPTIBLE TO FATIGUE
EN 755-2:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
EN 15085-4:2007 Railway applications - Welding of railway vehicles and components - Part 4: Production requirements
EN 15827:2011 Railway applications - Requirements for bogies and running gears

View more information
£36.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.