BS EN ISO 21225-1 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 1: REPLACEMENT ON THE LINE BY PIPE BURSTING AND PIPE EXTRACTION

Available format(s)

Hardcopy , PDF

Language(s)

English

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Design aspects
6 Material selection
7 Installation practice
8 Fitness for purpose
Annex A (normative) - Layered pipes
Annex B (Informative) - Pipe design considerations
particular to pipe bursting and pipe extraction
Bibliography

BS EN ISO 21225-1.

Committee	PRI/88/3
DocumentType	Draft
Pages	26
PublisherName	British Standards Institution
Status	NA

EN 681-4:2000/A2:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 4: CAST POLYURETHANE SEALING ELEMENTS
EN 1555-1:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-3:2010+A1:2012	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
ISO 4437-5:2014	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 5: Fitness for purpose of the system
EN 682:2002/A1:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
EN 15885:2010	Classification and characteristics of techniques for renovation and repair of drains and sewers
EN 681-1:1996/A3:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 4427-3:2007	Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings
BS PAS 128(2014) : 2014	SPECIFICATION FOR UNDERGROUND UTILITY DETECTION, VERIFICATION AND LOCATION
ISO 8772:2006	Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
ISO 4427-1:2007	Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General
EN 12201-3:2011+A1:2012	Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
EN 681-3:2000/A2:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 3: CELLULAR MATERIALS OF VULCANIZED RUBBER
ISO 11295:2017	Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 12176-1:2017	Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 4427-5:2007	Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system
ISO 4437-2:2014	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes
DVGW GW 312 : 2014
ISO 16010:2005	Elastomeric seals Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids
DVGW GW 322 : DRAFT 2001	NO-DIG REPLACEMENT OF GAS AND WATER PIPEWORK USING PUSHING OR PULLING PROCEDURES - REQUIREMENTS, QUALITY AND TESTING
EN 681-2:2000/A2:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
ISO 12176-2:2008	Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion
ISO 4437-1:2014	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 1: General
DVGW GW 323 : 2004 COR 2009	GRABENLOSE ERNEUERUNG VON GAS- UND WASSERVERSORGUNGSLEITUNGEN DURCH BERSTLINING - ANFORDERUNGEN, GUETESICHERUNG UND PRUEFUNG
DWA-M 143-15 : 2005	SANIERUNG VON ENTWAESSERUNGSSYSTEMEN AUSSERHALB VON GEBAEUDEN - TEIL 15: ERNEUERUNG VON ABWASSERLEITUNGEN UND -KANAELEN DURCH BERSTVERFAHREN
EN 12889:2000	Trenchless construction and testing of drains and sewers
EN 12201-5:2011	Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 12666-1:2005+A1:2011	Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
EN 12201-2:2011+A1:2013	Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
EN 1555-5:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 1555-2:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
ISO 4437-3:2014	Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings
EN 12201-1:2011	Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
NEN 3650-1 : 2012 + C1 2017	REQUIREMENTS FOR PIPELINE SYSTEMS - PART 1: GENERAL REQUIREMENTS
ISO 4633:2015	Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials
DVGW GW 304 : 2008
ISO 4427-2:2007	Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes
DVGW GW 325 : 2007	GRABENLOSE BAUWEISEN FUER GAS- UND WASSER-ANSCHLUSSLEITUNGEN - ANFORDERUNGEN, GUETESICHERUNG UND PRUEFUNG