We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ANSI HGV 3.1 : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    FUEL SYSTEM COMPONENTS FOR COMPRESSED HYDROGEN GAS POWERED VEHICLES

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-05-2019

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  Canadian Standards Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Preface
    1 Scope
    2 Reference publications
    3 Definitions
    4 General requirements
    5 General test methods
    6 Quality assurance
    7 Inspection and acceptance testing
    8 Check valve
    9 Manual valve
    10 Manual container valve
    11 Automatic valve and automatic container valve
    12 Gas injector
    13 Pressure sensors and pressure gauges
    14 Pressure regulator
    15 Pressure relief valve
    16 Pressure relief device
    17 Excess flow valve
    18 Gas-tight housing and leakage capture lines and passages
    19 Stainless steel rigid fuel line
    20 Flexible fuel line
    21 Filter housings
    22 Fitting
    23 Non-metallic low pressure rigid fuel line
    24 Discharge line closures
    Annex A (Informative) - Extreme thermal cycling test

    Abstract - (Show below) - (Hide below)

    Sets up requirements for newly produced compressed hydrogen gas fuel system components, intended for use on hydrogen gas powered vehicles as listed below: a) check valves; b) manual valves; c) manual container valves; d) automatic valves; e) gas injectors; f) pressure indicators; g) pressure regulator; h) pressure relief valves; i) pressure relief devices; j) excess flow valves; k) gas-tight housing and leakage capture lines and passages; l) rigid fuel lines; m) flexible fuel lines; n) filter housing; o) fittings; and p) discharge line closures.

    General Product Information - (Show below) - (Hide below)

    Committee NGV 3/HGV 3
    Development Note Supersedes CSA HGV 3.1. (03/2015)
    Document Type Standard
    Publisher Canadian Standards Association
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CSA HPIT 1 : 2015 COMPRESSED HYDROGEN POWERED INDUSTRIAL TRUCK ON-BOARD FUEL STORAGE AND HANDLING COMPONENTS
    CSA HPIT 1:15 (R2020) Compressed hydrogen powered industrial truck on-board fuel storage and handling components

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 15916:2015 Basic considerations for the safety of hydrogen systems
    ASTM A 632 : 2004 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service
    ASTM F 1802 : 2015 : REDLINE Standard Test Method for Performance Testing of Excess Flow Valves
    ISO 6270-2:2005 Paints and varnishes Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensation-water atmospheres
    ANSI HPRD 1 : 2013(R 2018) THERMALLY ACTIVATED PRESSURE RELIEF DEVICES FOR COMPRESSED HYDROGEN VEHICLE FUEL CONTAINERS
    ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
    ISO 14687-2:2012 Hydrogen fuel Product specification Part 2: Proton exchange membrane (PEM) fuel cell applications for road vehicles
    ISO/TS 16949:2009 Quality management systems Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations
    SAE J 1673 : 2012 HIGH VOLTAGE AUTOMOTIVE WIRING ASSEMBLY DESIGN
    ANSI/CSA CHMC 1-2014 (R2018) Test methods for evaluating material compatibility in compressed hydrogen applications - Metals
    IEEE/ASTM SI 10 : 2010 METRIC PRACTICE
    ISO 1431-1:2012 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
    ASTM G 154 : 2016 : REDLINE Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials
    SAE J 2578 : 2014 RECOMMENDED PRACTICE FOR GENERAL FUEL CELL VEHICLE SAFETY
    ISO 80000-1:2009 Quantities and units Part 1: General
    ISO 9001:2015 Quality management systems - Requirements
    SAE J 2579 : 2013 STANDARD FOR FUEL SYSTEMS IN FUEL CELL AND OTHER HYDROGEN VEHICLES
    ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
    SAE J 2719 : 2005(R2015) HYDROGEN FUEL QUALITY FOR FUEL CELL VEHICLES
    ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
    CSA HGV 4.2 : 2013 HOSES FOR COMPRESSED HYDROGEN FUEL STATIONS, DISPENSERS AND VEHICLE FUEL SYSTEMS
    AIAA G 095 : 2004 GUIDE TO SAFETY OF HYDROGEN AND HYDROGEN SYSTEMS
    SAE J 1742 : 2010 CONNECTIONS FOR HIGH VOLTAGE ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES - TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective