We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASME RTP 1 : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-08-2019

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  American Society of Mechanical Engineers

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Statement of Policy on the Use of Certification Marks and
    Code Authorization in Advertising
    Statement of Policy on the Use of ASME Marking to Identify
    Manufactured Items
    Committee Roster
    Introduction
    Summary of Changes
    Part 1 - General Requirements
    Part 2 - Materials
    Part 3 - Design
    Part 4 - Fabrication
    Part 5 - Overpressure Protection
    Part 6 - Inspection and Tests
    Part 7 - Shop Qualification
    Part 8 - Certification

    Abstract - (Show below) - (Hide below)

    Pertains to stationary vessels used for the storage, accumulation, or processing of corrosive or other substances at pressures not exceeding 15 psig external and/or 15 psig internal above any hydrostatic head.

    General Product Information - (Show below) - (Hide below)

    Development Note Effective date: 27-05-2018. (12/2017)
    Document Type Standard
    Publisher American Society of Mechanical Engineers
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN ISO 14692-2:2017 PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 2: QUALIFICATION AND MANUFACTURE (ISO 14692-2:2017)
    EEMUA 225 : 1920 ABOVE GROUND PLASTIC TANKS - A GUIDE TO THEIR SPECIFICATION, INSTALLATION, COMMISSIONING, INSPECTION, MAINTENANCE, REPAIR AND DISPOSAL
    CSA N285.5 : 2013 PERIODIC INSPECTION OF CANDU NUCLEAR POWER PLANT CONTAINMENT COMPONENTS
    PIP VESFG001 : 2011 FIBERGLASS TANK AND VESSEL SPECIFICATION
    OLF 055 : 1997 RECOMMENDED GUIDELINES FOR NDT OF GRP PIPE SYSTEMS AND TANKS
    ASME PTB 2 : 2009 GUIDE TO LIFE CYCLE MANAGEMENT OF PRESSURE EQUIPMENT INTEGRITY
    API 574 : 2016 INSPECTION PRACTICES FOR PIPING SYSTEM COMPONENTS
    API 574 CHINESE : 2009 INSPECTION PRACTICES FOR PIPING SYSTEM COMPONENTS
    AWS B2.4 : 2012 SPECIFICATION FOR WELDING PROCEDURE AND PERFORMANCE QUALIFICATION FOR THERMOPLASTICS
    PIP VEEFG001 : 2011 FIBERGLASS TANK AND VESSEL DESIGN GUIDELINES
    AWS G1.6 : 2006 SPECIFICATION FOR THE QUALIFICATION OF PLASTICS WELDING INSPECTORS FOR HOT GAS, HOT GAS EXTRUSION, AND HEATED TOOL BUTT THERMOPLASTIC WELDS
    API 574 REDLINE : 2009 INSPECTION PRACTICES FOR PIPING SYSTEM COMPONENTS
    EN ISO 14692-2:2017 PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 2: QUALIFICATION AND MANUFACTURE (ISO 14692-2:2017)
    ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture

    Standards Referencing This Book - (Show below) - (Hide below)

    ASME PV CODE 5 : 2017 BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION
    ASTM D 3307 : 2016 : REDLINE Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
    ASTM D 5162 : 2015 : REDLINE Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates
    ASME PV CODE 2C : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS
    ASTM D 5083 : 2017 : REDLINE Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
    ASTM D 1248 : 2016 : REDLINE Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
    ASTM D 3159 : 2015 : REDLINE Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials
    ASME PV CODE 2A : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - FERROUS MATERIAL SPECIFICATIONS (BEGINNING TO SA-450) AND (SA-451 TO END)
    ASME PV CODE 2B : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - NONFERROUS MATERIAL SPECIFICATIONS
    ASTM D 3294 : 2015 : REDLINE Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes
    ASTM D 3368 : 2017 : REDLINE Standard Specification for FEP Sheet and Film
    NFPA 255 : 2006 TEST OF SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS
    ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
    ASTM D 4285 : 1983 : R2018 Standard Test Method for Indicating Oil or Water in Compressed Air
    ASTM D 1781 : 1998 Standard Test Method for Climbing Drum Peel for Adhesives
    UL 723 : 2010 TEST FOR SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS
    MIL HDBK 17-3 : F COMPOSITE MATERIALS HANDBOOK - VOLUME 3: POLYMER MATRIX COMPOSITES MATERIALS USAGE, DESIGN, AND ANALYSIS
    AWS B2.4 : 2012 SPECIFICATION FOR WELDING PROCEDURE AND PERFORMANCE QUALIFICATION FOR THERMOPLASTICS
    ASTM C 581 : 2015 : REDLINE Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
    ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
    ASME PV CODE 2D CUSTOMARY : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (CUSTOMARY)
    ASTM D 2241 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
    ASME PV CODE 8 DIV 2 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES
    ASME B31.3:2016 PROCESS PIPING
    BS 6399-2(1997) : 1997 LOADING FOR BUILDINGS - PART 2: CODE OF PRACTICE FOR WIND LOADS
    ASME PV CODE 2D METRIC : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (METRIC)
    BS 4994(1987) : 1987 SPECIFICATION FOR DESIGN AND CONSTRUCTION OF VESSELS AND TANKS IN REINFORCED PLASTICS
    ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
    ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
    ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM D 1593 : 2013 : REDLINE Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
    API 650 : 2013 WELDED TANKS FOR OIL STORAGE
    ASME PV CODE 8 DIV 3 : 2017 BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS
    ISO 14130:1997 Fibre-reinforced plastic composites Determination of apparent interlaminar shear strength by short-beam method
    AWS D1.1 : 2000 STRUCTURAL WELDING CODE - STEEL
    ASME CA 1 : 2014 CONFORMITY ASSESSMENT REQUIREMENTS
    AWS G1.10M : 0 GUIDE FOR THE EVALUATION OF THERMOPLASTIC WELDS
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    ASTM D 1784 : 2011 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective