We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM A 463/A463M : 2022

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  07-11-2022

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This specification covers aluminum-coated steel sheet in coils and cut lengths available with two types of aluminum coating applied by the hot-dip process, with several coating weights [masses].

    1.2Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M, unless otherwise provided herein.

    1.3The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

    1.4Units—This specification is applicable to orders in either inch-pound units (as A463) or SI units [as A463M]. Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

    1.5Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units.

    1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee A 05
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM C 1146 : 2009 : R2018 Standard Guide for Prefabricated Panel and H-bar Insulation Systems for Vessels, Ducts and Equipment Operating at Temperatures Above Ambient Air
    ASTM E 1514 : 1998 : R2017 : EDT 1 Standard Specification for Structural Standing Seam Steel Roof Panel Systems
    ASTM A 755/A755M : 2018 Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
    ASTM C 1047 : 2019 Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
    ASTM A 1092 : 2015 : R2020 Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
    ASTM A 787/A787M : 2020 : REV A Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing
    ASTM A 754/A754M : 2021 Standard Test Method for Coating Weight [Mass] of Metallic Coatings on Steel by X-Ray Fluorescence
    ASTM A 1122/A1122M : 2022 Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion
    ASTM A 924/A924M : 2022 : REV A Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
    ASTM A 1003/A1003M : 2015 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective