Name: ASTM A 682/A682M : 2005
Brand: ASTM

ASTM A 682/A682M : 2005

Superseded

View Superseded by

Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For (Withdrawn 2009)

Superseded date

31-10-2009

Published date

31-12-2010

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 01.03, 2009 Defines general requirements for cold rolled carbon spring steel strip in cut lengths or coils. Covers strip 0.3000 inch (7.6 mm) or less in thickness and over 1/2 to 23 15/16 inch (12.5 to 600 mm) in width, inclusive. Other widths may be available by agreement between purchaser and supplier, but such products are technically classified as cold-rolled sheet. Maximum specified carbon range is over 0.25 % up to and including 1.35 %, inclusive. This applies to cold-rolled carbon spring steel strip supplied under ASTM A 684/A 684M.

1.1 This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6 mm) or less in thickness and over 1/2 to 23 15/16 in. (12.5 to 600 mm) in width, inclusive. Strip tolerance products may be available in widths wider than 2315/16 in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet.

1.2 The maximum of the specified carbon range is over 0.25 % to 1.35 %, inclusive.

1.3 The above shall apply to the cold-rolled carbon spring steel strip furnished under each of the following specifications issued by ASTM:

Title of SpecificationASTMDesignationSteel, Strip, High Carbon,Cold Rolled A 684/A 684M

1.4 The tolerances in this specification are different than those in Specification A 568/A 568M and Specification A 109/A 109M.

1.5 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.

1.6 The metric portions of the tables herein list permissible variations in dimensions and mass (see Note 0) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the "M" specification is used.

Note 1—The term weight is used when inch-pound units are the standard. However, under SI the preferred term in mass.

1.7 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.

1.8 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.

Committee	A 01
DevelopmentNote	Supersedes ASTM A 682M and ASTM A 682 (05/2002)
DocumentType	Standard
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM A 684/A684M : 2017 : REDLINE
Supersedes	ASTM A 682/A682M : 2002

ISO 8000-110:2009	Data quality Part 110: Master data: Exchange of characteristic data: Syntax, semantic encoding, and conformance to data specification
BS ISO 4960:2007	Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 %
ASHRAE 97 : 2007(RA2017)	Sealed Glass Tube Method to Test the Chemical Stability of Materials for Use within Refrigerant Systems<br>
ISO 4960:2007	Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 %
ISO/TS 8000-110:2008	Data quality Part 110: Master data: Exchange of characteristic data: Syntax, semantic encoding, and conformance to data specification

SAE J 1086 : 2012	NUMBERING METALS AND ALLOYS
MIL-STD-129 Revision R:2014	Military Marking for Shipment and Storage
ASTM A 684/A684M : 2017 : REDLINE	Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled
FED-STD-123 Revision H:2007	MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM E 527 : 2016 : REDLINE	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM A 700 : 2014	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
MIL-STD-163 Revision C:1978	STEEL MILL PRODUCTS PREPARATION FOR SHIPMENT AND STORAGE
FED-STD-183 Revision C:1980	CONTINUOUS IDENTIFICATION MARKING OF IRON AND STEEL PRODUCTS