We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM B 111/B111M : 2008 : REV A

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  01-10-2008

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified: (WarningMercury is a definite health hazard in use and disposal. (See 12.1.))

    Copper or
    UNS No.
    C10100OFEOxygen-free electronic
    C10200OFAOxygen-free without residual deoxidants
    C10300. . .Oxygen-free, extra low phosphorus
    C10800. . .Oxygen-free, low phosphorus
    C12000DLPAPhosphorized, low residual phosphorus
    C12200DHPAPhosphorized, high residual phosphorus
    C14200DPAAPhosphorized, arsenical
    C19200. . .Phosphorized, 1 % iron
    C23000. . .Red Brass
    C28000. . .Muntz Metal
    C44300. . .Admiralty Metals, B, C, and D
    C60800 . . . Aluminum Bronze
    C61300. . .. . .
    C61400. . .Aluminum Bronze, D
    C68700. . .Aluminum Brass, B
    C70400. . .95-5 Copper-Nickel
    C70600. . .90-10 Copper-Nickel
    C70620. . .90-10 Copper-NickelWelding Grade
    C71000. . .80-20 Copper-Nickel
    C71500. . .70-30 Copper-Nickel
    C71520. . .70-30 Copper-NickelWelding Grade
    C71640. . .Copper-nickel-iron-manganese
    C72200. . .. . .

    A Designations listed in Classification B 224.

    1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee B 05
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    • Access your standards online with a subscription


      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective