• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM B 160 : 2005 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Nickel Rod and Bar
Available format(s)

Hardcopy , PDF

Superseded date

04-03-2021

Language(s)

English

Published date

01-05-2005

CONTAINED IN VOL. 02.04, 2015 Specifies the nickel (UNS N02200), low carbon nickel (UNS N02201), and solution strengthened nickel (UNS N02211) in the form of hot-worked and cold-worked rod and bar.

1.1 This specification covers nickel (UNS N02200)*, low carbon nickel (UNS N02201)*, and solution strengthened nickel (UNS N02211) in the form of hot-worked and cold-worked rod and bar in the conditions shown in Table 1.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

TABLE 1 Mechanical Properties

Condition and Diameter or Distance
Between Parallel Surfaces, in. (mm)
Tensile Strength, min,
psi (MPa)
Yield Strength (0.2 % offset),
min. psi (MPa)A
Elongation in 2 in. or 50 mm or 4D, min %
Nickel (UNS N02200)
Cold-worked (as worked):
Rounds, 1 (25.4) and under 80 000 (550) 60 000 (415) 10B
Rounds over 1 to 4 (25.4 to 101.6) incl. 75 000 (515) 50 000 (345)15
Squares, hexagons, and rectangles, all sizes 65 000 (450) 40 000 (275) 25B
Hot-worked:
All sections, all sizes 60 000 (415) 15 000 (105) 35C
Rings and disksD
Annealed:
Rods and bars, all sizes 55 000 (380) 15 000 (105) 40B
Rings and disksE
Forging quality
All sizes F FF
Low-Carbon Nickel (UNS N02201) and Solution Strengthened Nickel (UNS N02211)
Hot-worked:
All sections, all sizes 50 000 (345) 10 000 (70) 40C
Annealed:
All products, all sizes 50 000 (345) 10 000 (70) 40B

A See 12.2.

B Not applicable to diameters or cross sections under 3/32 in. (2.4 mm).

C For hot-worked flats 5/16 in. (7.9 mm) and under in thickness the elongation shall be 25%, min.

D Hardness B45 to B80, or equivalent.

E Hardness B45 to B70 or equivalent.

F Forging quality is furnished to chemical requirements and surface inspection only. No tensile properties are required.

Committee
B 02
DocumentType
Standard
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded

ASTM B 162 : 1999 Standard Specification for Nickel Plate, Sheet, and Strip
ASTM F 85 : 1976 : R2002 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes
AWS BRH:2007 BRAZING HANDBOOK
ASTM F 85 : 1976 : R2009 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes
BS EN ISO 4126-2:2003 Safety devices for protection against excessive pressure Bursting disc safety devices
ASTM F 85 : 1976 : R1997 : EDT 1 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes
ASME B16.34 : 2017 VALVES - FLANGED, THREADED, AND WELDING END
DOD-HDBK-249 Revision A:1984 METALS AND ALLOYS RAPID ON-SITE IDENTIFICATION OF (RECOMMENDED PROCEDURE FOR CHEMICAL SPOT TESTING AND ASSOCIATED PHYSICAL TESTS TO VERIFY METAL ALLOY CLASSIFICATION) (METRIC)
AWWA C504 : 2015 RUBBER-SEATED BUTTERFLY VALVES
ASTM F 85 : 1976 : R2018 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes (Withdrawn 2023)
EN ISO 4126-2:2003/AC:2006 SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - PART 2: BURSTING DISC SAFETY DEVICES
ASME PV CODE 2C : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS
ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
ASME B31.3:2016 PROCESS PIPING
ASTM B 162 : 1999 : R2009 Standard Specification for Nickel Plate, Sheet, and Strip
15/30299570 DC : 0 BS ISO 7195 - NUCLEAR ENERGY - PACKAGINGS FOR THE TRANSPORT OF URANIUM HEXAFLUORIDE (UF[6])
AWWA C520 : 2014 KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM)
I.S. EN ISO 4126-2:2003 SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - PART 2: BURSTING DISC SAFETY DEVICES
ASTM F 85 : 1976 : R2013 Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes
ASTM G 134 : 2017 : REDLINE Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet
NF ISO 7195 : 2005 NUCLEAR ENERGY - PACKAGING OF URANIUM HEXAFLUORIDE (UF6) FOR TRANSPORT
ISO 7195:2005 Nuclear energy Packaging of uranium hexafluoride (UF6) for transport
CSA C22.2 No. 124 : 2016 MINERAL-INSULATED CABLE
ASTM B 162 : 1999 : R2005 Standard Specification for Nickel Plate, Sheet, and Strip
ISO 4126-2:2003 Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices
UNI EN ISO 4126-2 : 2003 SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - BURSTING DISC SAFETY DEVICES
ASTM B 162 : 1999 : R2014 Standard Specification for Nickel Plate, Sheet, and Strip
ASTM G 32 : 2016 : REDLINE Standard Test Method for Cavitation Erosion Using Vibratory Apparatus

ASTM E 1473 : 2016 : REDLINE Standard Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ASTM E 8 : 2004 Standard Test Methods for Tension Testing of Metallic Materials

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.