ASTM B 241/B241M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
12-11-2022
English
24-02-2016
1.1 This specification2 covers aluminum and aluminum–alloy seamless pipe in the alloys (Note 1) and tempers shown in Table 1 [Table 2] and seamless extruded round tube in the alloys and tempers shown in Table 3 [Table 4] intended for pressure applications.
1.1This specification2 covers aluminum and aluminum–alloy seamless pipe in the alloys (Note 1) and tempers shown in Table 1 [Table 2] and seamless extruded round tube in the alloys and tempers shown in Table 3 [Table 4] intended for pressure applications. The standard sizes for seamless pipe are listed in Table 16.7 of ANSI H35.2 and H35.2(M). Nonstandard alloys, tempers, and sizes of pipe are produced as seamless extruded tube. Also included in this standard are seamless extruded pipe and seamless extruded tube for Oil & Gas Transmission previously covered under Specification B345/B345M.
Note 1:Throughout this specification, use of the term alloy, in the general sense, includes aluminum as well as aluminum alloy.
Note 2:For drawn seamless tubes, see Specifications B210 and B210M; for extruded tubes, Specifications B221 and B221M; for drawn seamless tubes for condensers and heat exchangers, Specifications B234 and B234M; for seamless condenser and heat exchanger tubes with integral fins, Specification B429/B429M; and for drawn tube for general purpose applications, Specifications B483/B483M.
1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 5 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4.1The SI units are shown either in brackets or in separate tables.
| Committee |
B 07
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM B 210/B210M : 2019 : REV A | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes |
| ASTM B 361 : 2016 | Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings |
| ASTM E 127 : 2020 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks |
| ASTM B 483/B483M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM B 221 : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM C 1802 : 2020 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM B 234M : 2017 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| ASTM B 429/B429M : 2020 | Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube |
| ASTM B 221M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
| ASTM E 2375 : 2016 | Standard Practice for Ultrasonic Testing of Wrought Products |
| ASTM B 234 : 2017 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| ASTM B 881 : 2017 | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
| ASTM B 483/B483M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM E 1251 : 2007 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
| ASTM B 483/B483M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM E 1004 : 2009 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 945 : 2006 : R2014 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10–Type Tempers |
| ASTM B 557M : 2002 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric] |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 1251 : 1994 : R1999 | Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge |
| ASTM E 716 : 2016 : R2021 : EDT 2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 660 : 2021 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM E 1251 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM E 716 : 2016 : R2021 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM B 221M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
| ASTM B 594 : 2019 : EDT 1 | Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products |
| ASTM B 221 : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM E 1004 : 1999 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 1004 : 2002 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
| ASTM E 716 : 2016 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 557M : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric] |
| ASTM B 660 : 2015 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM B 594 : 2019 | Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products |
| ASTM B 221M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
| ASTM E 1251 : 2004 | Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
| ASTM E 1004 : 2017 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
| ASTM B 557 : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| ASTM E 1251 : 2011 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM E 716 : 2016 : R2021 : EDT 1 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 221M : 2005 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric] |
| ASTM B 945 : 2021 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers |
| ASTM B 221M : 2000 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric] |
| ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
| ASTM B 221 : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM B 221 : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.